Bosch Professional GAS 18V-10 L Manual Original página 11

Battery model ProCORE18V...
LEDs
5× continuous green light
4× continuous green light
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light
Inserting and Removing the Battery
(see figures A1−A2)
Do not use force to insert the battery. The battery is de-
u
signed in such a way that it can only be inserted into the
product when it is in the right position.
Keep the battery compartment and the battery bay clean
u
and dry at all times to ensure good, safe operation.
– Press the release button (11) to open the battery com-
partment cover (12).
– Slide the battery (20) into the battery bay (19) until it
audibly clicks into place.
– To remove the battery (20), press the release
button (21) on the battery and pull it out of the battery
bay (19).
– Close the battery compartment cover (12).
Changing the Battery Compartment Cover
(see figures A3−A5)
If you wish to use a ProCORE18V 12Ah battery, the battery
compartment cover (12) can then no longer be closed. In
this case, the battery compartment cover (12) can be re-
placed with a screen (23) designed for this purpose.
In damp or wet conditions, the dust extractor may only be
used with the battery compartment cover closed.
Removing the Battery Compartment Cover
(see figure A3)
Remove the battery (20) from the battery bay (19).
Remove the two fastening screws (22) (ST4×12) with a
cross-headed screwdriver PH1 and take off the battery com-
partment cover (12).
Inserting the Screen (see figure A4)
Press the battery compartment cover bracket (24) down-
wards and slide on the screen (23).
Removing the Screen (see figure A5)
Apply a slot screwdriver, push the screen (23) a little way to-
wards the rear and remove the screen. When doing so, press
the battery compartment cover bracket (24) downwards.
Bosch Power Tools
Fitting the Brackets for Extractor Accessories
(see figure B)
– Slide the bracket (25) for the suction tube and crevice
nozzle firmly into the adapter (10) provided for it from
Capacity
above until it clicks into place.
80−100 %
– Slide the bracket (27) for the vacuum hose and floor
nozzle firmly into the adapter (7) provided for it from
60−80 %
above and tighten the fixing bolts (26).
40−60 %
20−40 %
Fitting the vacuum hose (see figure C)
5−20 %
– Insert the vacuum hose (13) into the hose adapter (8) un-
0−5 %
til both snap fasteners (28) of the vacuum hose click into
place.
Note: The friction generated by the dust in the vacuum hose
and accessory during extraction causes an electrostatic
charge that the user may experience as static discharge (de-
pending on environmental factors and their physiological
state).
Fitting the Vacuuming Accessories
The vacuum hose (13) is equipped with a clip system which
can be used to connect vacuuming accessories (dust extrac-
tion adapter (14), curved nozzle (15)).
Fitting the extraction adapter or curved nozzle
(see figure D)
– Fit the extraction adapter (14) or the curved nozzle (15)
to the vacuum hose (13) until the two snap
fasteners (28) on the vacuum hose audibly click into
place.
– To remove the adapter, press the snap fasteners (28) in-
wards and pull apart the components.
Fitting the Nozzles and Tubes
– If required, place the suction tubes (18) firmly inside one
another and then attach them firmly to the curved nozzle
(15).
– Attach the floor nozzle (17) or the crevice nozzle (16)
firmly to the suction tube (18) or the curved nozzle (15).
Attaching the carrying strap (see figure E)
The carrying strap is only intended for carrying and at-
u
taching the dust extractor and not as a safety harness.
Click the snap hooks of the carrying strap (29) into the
fastening eyes (9) of the dust extractor.
Fitting the Rollers (see figure F)
Insert the 4 fastening pins on the rollers (30) into the roller
adapters (31) until they audibly click into place.
Other rollers can also be used as per the EN 12529 standard
(11 mm fastening pin diameter).
Check the functionality of the roller brakes before us-
u
ing the dust extractor.
English | 11
1 609 92A 6PF | (26.07.2021)