Publicidad
Idiomas disponibles
Idiomas disponibles
CARPET HEIGHT ADJUSTMENT
MED
A
To adjust height setting, TURN knob (A) to desired
height setting.
For maximum cleaning performance,
the following carpet height settings are
recommended:
• Bare-floor setting (1): for bare floors.
• Low setting (2): for all types of carpet.
• Higher settings: for very deep pile carpet,
where easier pushing effort is desired, while
maintaining good cleaning performance.
IMPORTANT: If the vacuum is difficult to push
turn knob to the next higher setting.
REMOVING HOSE
When using cleaning tools, place cleaner handle
in the upright position. To remove hose for tool
use, press the hose release button and pull hose
end out. To lock back into place, push hose into
hose tube until you hear a click.
ATTACH WAND AND TOOLS
(Tools may vary per model)
WARNING:
Unplug before connecting
Air-Powered Hand Tool.
A
B
1. Attach tool or wand to the hose (A).
2. Attach tool to wand (B) by pushing it firmly
onto the wand.
3. Twist wand or tool slightly to tighten or loosen
the connection.
4. To extend wand, twist counter-clockwise to
the unlocked position, extend wand & twist
clockwise until tight. Reverse to collapse.
HOW TO CLEAN TOOLS
To clean Hose and Turbo Tool, wipe with a damp
cloth. DO NOT submerge in water. Other cleaning
tools may be washed in warm water with a mild
detergent. Rinse and air dry 24 hours before
using. (Tool varies per model)
STAIR CLEANING
NOTE: Lift vacuum by Stair Cleaning Handle and
position on stairs. Clean forward to back. Never
leave the vacuum standing on stairs when not
cleaning.
CAUTION:
Use extra care when
cleaning on stairs. To avoid personal injury or
damage, and to prevent the cleaner from falling,
always place cleaner at bottom of stairs on
floor. Do not place cleaner on stairs or furniture,
as it may result in injury or damage. When
using tools, always ensure handle is in upright
position.
CORD STORAGE
Wrap cord around hooks for convenient storage.
Attach the plug end to the cord.
MAINTENANCE
This product contains no serviceable parts. If
appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, call customer service at 1-800-944-9200
prior to continuing use.
A
The System Check Indicator located at (A), alerts
you to possible system performance issues.
Any other servicing should be done by an
authorized service representative.
NOTICE: A Thermal Protector has been designed
into your cleaner to protect it from overheating.
When the thermal protector activates the
cleaner will stop running.
If this happens proceed as follows:
1. Turn cleaner OFF and unplug it from the
electrical outlet.
2. Empty dirt cup.
3. Inspect the nozzle inlet, hose connector,
hose, dirt cup inlet, cyclonic filter, rinsable
filter, and HEPA filter for any obstructions.
Clear obstructions if present.
When cleaner is unplugged and motor has
cooled for 30 minutes, the thermal protector
will deactivate and cleaning may continue.
If the thermal protector continues to activate
after following the above steps, your cleaner
needs servicing.
DIRT CUP
WHEN TO EMPTY
A
To maintain optimal performance, empty the dirt
cup before the dirt cup reaches the max line (A).
Place the vacuum in the upright position before
removing the dirt cup.
WARNING:
To reduce the risk of
personal injury - Unplug before cleaning or
servicing. Do not use vacuum without dirt cup or
filters in place. Very fine materials, such as face
powder or cornstarch, may seal the filter and
cause a reduction in performance. When using
the vacuum for this type of dust, empty the cup
and clean the filters often.
HOW TO EMPTY
A
1
Press dirt cup release button (A) and pivot cup
out.
C
B
D
2
Hold dirt cup over trash receptacle, push dirt cup
door release lever (B) to open dirt cup door (C).
Close dirt cup door (C). Press firmly to secure at
front (D).
3
Place bottom of dirt cup into vacuum body first.
Pivot dirt cup into vacuum body and press firmly
until it locks into place.
FILTERS: WHEN TO CLEAN
WARNING:
To reduce the risk of
personal injury - Unplug before cleaning or
servicing. Do not use vacuum without dirt cup
or filters in place.
To maintain optimal performance, filters should
be cleaned at least every two months under
normal use.
RINSABLE FILTER: HOW TO CLEAN
1
Pull up on dirt cup latch to open.
2
Pull on filter by the pocket to remove rinsable
filter. Hold filter under running water for at least
two minutes to remove dirt and debris. Squeeze
filter twice while underwater. Remove from water
and squeeze a final time to remove excess water.
WHAT TO BUY: Rinsable Filter
When used and maintained properly, your
Rinsable Filter should not need replacement
within the warranty period. If desired, additional
filter is available at Hoover.com or call
1-800-944-9200. Ask for Hoover® Part No.
304087001
IMPORTANT: Allow filter to dry completely before
replacing. Dry filter on edge so air circulates on
both sides of filter. This may take up to 48 hours.
1. Replace filter with pocket and graphics facing
up.
2. Close lid securely by pushing until it clicks.
3. Replace dirt cup as described on page 2.
FILTER MADE WITH HEPA MEDIA:
HOW TO CLEAN
WARNING:
To reduce the risk of
personal injury - Unplug before cleaning or
servicing. Do not use vacuum without dirt cup
or filters in place.
WHAT TO BUY: CARBON FILTER
Carbon Filter may need to be replaced more often
to maintain optimal odor absorbing effectiveness.
Additional filter is available at Hoover.com or
call 1-800-944-9200. Ask for Hoover® Part
902404001.
Publicidad
