Bosch Nexxt 800 Serie Operacion, Cuidado E Instrucciones Para La Instalacion página 10

Mobile home kit
partno.WTZ1275
Note:
Please c heckwiththeAuthority H aving
Jurisdiction inyourarea toverify ifa gas
dryer c anbeinstalled i nyourmobile
home. O nce thathasbeen verified,
installation ofthedryershall c onform to
theManufactured Home Construction
andSafety S tandard, Title 24CFR, P art
3280{formerly theFederal Standard f or
Mobile Home Construction andSafety,
Title 24,HUD (Part 2 80)}, a nd/or
Standard C AN/CSA-Z240 MH.
Please u semobile home kitnumber
WTZ1275 formeans t o secure the
dryer t othestructure.
Seepage 9 "Exhaust AirConnection"
fortheexhaust ductinstallation
instructions.
Theexhaust ductmustbesecurely
fastened t o a noncombustible portion
ofthemobile home structure a ndmust
notterminate b eneath t hemobile
home.
Anopening t otheoutside mustbe
provided d uringinstallation. Insure that
thefreearea oftheopening f orthe
introduction ofoutside airis notless
thantwicethearea ofthedryerexhaust
outlet o ruseatleast a 5 inchdiameter
exhaust or atleast a 25in2square
exhaust ductfortheopening.
Installation - step by step
1. Unpack the dryer.
2. Remove all objects from the drum.
3. Check the dryer for visible
damage.
4. Position the dryer near the
installation location.
5. If required, have customer service
change the door hinges to the left
(see page 6).
6. If required, have customer service
install the exhaust air outlet on the
dryer (see page 8).
7. Have the gas supply connected by
an qualified technician (see page
7).
8. Install exhaust duct, if necessary.
Follow the installation instructions
supplied by the appropriate
manufacturer!
ITllf space is very restricted, it is
recommended to fit the initial parts
of the exhaust duct to the dryer
before the dryer is moved to its
final installation location.
9. Move the dryer to its final location
and align.
Do not slide dryer across the floor if
height-adjustable feet have been
extended. Feet and/or dryer base
may be damaged if dryer is slid
across floor with height adjustable
feet extended.
10. Position and then level the dryer.
The dryer should be level with all
four feet firmly on the ground. The
dryer must not wobble. If the dryer
is not level or if it does wobble, the
feet must be adjusted. Adjust the
height-adjustable feet until the
dryer does not rock and is level,
both front-to back and
side-to-side.
11. Connect the exhaust duct to the
exhaust air outlet on the dryer.
12. Insert plug into the wall receptacle.
Check list before using
the dryer
1. Check that steps 1-12 have been
implemented properly.
2. Ensure that the dryer is connected
to the power supply.
3. Open the shutoff-valve.
4. Read the operating instructions to
understand how your dryer
operates.
5. Conduct an appliance test:
Check that the drum is empty.
Close the dryer door.
Switch the dryer to "Extra Dry"
and then press the Start
button.
.
7.
After 3-5 minutes press the
Stop button and open the door.
If the interior of the dryer feels
warm, the dryer has been
connected properly.
Switch the dryer to "Off".
If the dryer does not work, switch
the dryer to "Off".
Look in the troubleshooting
section (page 22) of the
OPERATING INSTRUCTIONS and
find the fault.
Preparing to transport the
dryer- step by step
1. Close the shut-off valve.
2. Rotate the program selector to
"OFF".
3. Pull out the power supply plug
or
turn off the circuit breaker.
4. Disconnect gas supply
5. Disconnect the exhaust duct from
the exhaust air outlet on the dryer.
6. Place any accessories in the drum.
7. Close the door and secure with
adhesive tape.
8. Screw the height-adjustable feet of
the dryer into the housing to
prevent them from being damaged
during transportation.
10