Publicidad
Idiomas disponibles
Idiomas disponibles
performance, the burner and venturi tube assembly should be removed and cleaned whenever the barbeque
has been idle for an extended period of time.
Leak Testing Valves, Hose and Regulator
time the cylinder is changed or disconnected.
1. Turn all appliance control knobs to .
2. Be sure regulator is tightly connected to gas cylinder. 3. Turn on Gas. If you hear a rushing sound, turn gas off
immediately. There is a major leak at the connection. Correct before proceeding.
4. Brush soapy solution (mixture of half soap and half water) onto hose connections.
5. If growing bubbles appear, there is a leak. Turn off gas at cylinder immediately and check tightness of
connections. If leak cannot be stopped do not try to repair. Call for replacement parts.
6. Always turn off gas at cylinder after performing leak test.
IF APPLIANCE FAILS TO LIGHT
Ÿ
Make sure gas is turned on at cylinder.
Ÿ
Make sure there is gas in the cylinder.
Ÿ
Does the ignitor make a sparking noise?
If yes check for spark at burner.
If no spark check for damaged or loose wires.
Ÿ
If wires are OK check for cracked or broken electrode, replace if needed.
Ÿ
If wire or electrodes are covered by cooking residue, clean electrode tip with alcohol wipe if needed.
Ÿ
If needed replace wires.
Ÿ
If no sound check battery.
Ÿ
Make sure battery is installed correctly.
Ÿ
Check for loose wire connection at module and switch.
Cleaning the Burner Assembly
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting barbecue. 1. Turn gas
off at control knobs and LP cylinder. 2. Remove cooking
grates and heat tents.
3. Remove carryover tubes and hardware securing
burners. 4. Detach electrode from burner.
NOTE: Removal/Detachment method will depend on the
burner configuration. See different configurations in illustrations
below. 5. Carefully lift each burner up and away from valve
openings.
We suggest three ways to clean the burner tubes. Use
the one easiest for you.
A. Bend a stiff wire (a light weight coat hanger works well)
into a small hook. Run the hook through each burner
tube several times.
B. Use a narrow bottle brush with a flexible handle (do
not use a brass wire brush). Run the brush through
each burner tube several times.
C. Wear eye protection: Use an air hose to force air into
the burner tube and out the burner ports. Check each
port to make sure air comes out each hole.
6. Wire brush entire outer surface of burner to remove
food residue and dirt.
7. Clean any blocked ports with a stiff wire such as an
open paper clip.
8. Check burner for damage due to normal wear and
corrosion, some holes may become enlarged. If any large
cracks or holes are found, replace burner.
VERY IMPORTANT: Burner tubes must reengage
valve openings. See illustrations at right.
Leak test before first use, at least once a year, and every
Storing Your Appliance
Ÿ
If ignitor continues to not work then use match.
Correct burner-to
9. Attach electrode to burner.
10. Carefully replace burners.
11. Attach burners to brackets on firebox.
12. Reposition carryover tubes and attach to burners.
Replace heat tents and cooking grates.
13. Before cooking again on barbecue, perform a "Leak
Test" and "Burner Flame Check" .
Clean cooking grates.
Store in dry location.
When gas cylinder is connected to appliance, store outdoors in
a well-ventilated space and out of reach of children. Cover
appliance if stored outdoors.
Store appliance indoors ONLY if gas cylinder is turned off and
disconnected, removed from appliance and stored outdoors.
When removing appliance from storage check for burner
obstructions.
General Appliance Cleaning
Periodic cleaning of this grill is necessary, as grill fires can occur
when grease and food debris collect in the bottom of the grill.
After each use, remove any remaining food particles from the
cooking grate and inside of the grill using a Char-Broil Cool-Clean
Brush. Afterwards you could spray Char-Broil Grate Cleaner
generously onto the grate, allow it work for 10 minutes and wipe
off with a wet cloth or brush. Perform grill cleaning after the grill
has cooled down.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors of gas
barbecues are not painted at the factory (and should never
valve engagement
Publicidad
