Publicidad
Idiomas disponibles
Idiomas disponibles
Ignitor
Lighting
(continued)
8. Once each burner has ignited,
turn knobs to desired
setting.
9. If ignitor
does not work, follow
match lighting
instructions.
Turn controls and gas source or tank OFF when not
in use.
CAUTIo.
Burner Flame Check
= Remove cooking
grates and Heat Diffusers.
Light burners, rotate
knobs from HI to LOW. You should see a smaller flame in
LOW position
than seen on Hk Perform
burner flame check
on sideburner,
also. Always
check flame
prior to each use. If
only low flame
is seen refer to "Sudden
drop or low flame"
in
the Troubleshooting
Section.
_W
If ignition does NOT occur in 5 seconds, turn the
burner controls OFF,wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
Do not lean over grill while
lighting.
1. Open lld. Turn ON gas at LP cylinder.
2. Place match into match holder (hanging
from side panel of
grill).
Light match; then light burner by placing
match through
the match light hole on right or left side of grill.
3. Push in and turn far right or far left burner knob to the Hi
position,
depending
on match light hole selected.
Be sure
burner lights and stays lit.
4. Light adjacent
burners in sequence by pushing knobs in and
turning to the HI position.
Sideburner
Ignitor
Lighting
Do not lean over grlll while
lighting.
1. Open sideburner
lld. Turn ON gas at LP cylinder.
2. Turn sideburner
knob to the HI position,
push and hold
ELECTRONIC
iGNiTiON
button.
3. If sideburner
does NOT light within 5 seconds, turn knob to
OFF, wait 5 minutes, then
repeat lighting
procedure.
Sideburner
Match
Lighting
1. Open sldeburner
lld. Turn ON
gas at LP cylinder.
2. Place lit match near burner.
3. Turn sideburner
knob to the
Hi position.
Be sure burner lights and
stays lit.
12 ° 464424312
° 464424512
Turning
Grill
Off
* Turn all knobs to the OFF position. Turn LP cylinder
OFF by
turning hand-wheel
clockwise
to a full stop.
Ignitor
Check
* Turn gas off at LP cylinder.
Press and hold electronic
ignitor
button.
A "Click"
should be heard and spark seen each time
between
each collector
box or burner and electrode.
See
"Troubleshooting"
if no click or spark.
Valve
Check
* Important:
Make sure gas is off at LP cylinder
before
checking
valves.
Knobs lock in OFF position.
To check
valves, first push in knobs and release, knobs should spring
back. If knobs do not spring back, replace
valve assembly
before
using grill. Turn knobs to LOW position
then turn back to
OFF position. Valves should turn smoothly.
Hose Check
" Before each use, check to see if hoses are cut or worn.
Replace damaged
hoses before using grill. Use only
identical
replacement
part valve/hose/regulator
as
specified
in the Parts List of this Use and Care Guide.
General
Grill
Cleaning
* Do not mistake
brown or black accumulation
of grease and
smoke for paint.
Interiors of gas grills are not painted
at the
factory
(and should
never be painted).
Apply
a strong solution
of detergent
and water or use a grill cleaner
with scrub brush
on insides of grill lid and bottom.
Rinse and allow to completely
air dry. Do not apply
a caustic grill/oven
cleaner
to painted
surfaces.
" Plastic parts: Wash
with warm
soapy water
and wipe dry.
Do not use citrisol, abrasive
cleaners,
degreasers
or a
concentrated
grill cleaner
on plastic parts. Damage
to and
failure
of parts can result.
* Porcelain
surfaces:
Because of glass-like
composition,
most
residue can be wiped
away with baking
soda/water
solution or
specially
formulated
cleaner. Use nonabrasive
scouring
powder
for stubborn
stains.
* Painted
surfaces:
Wash
with mild detergent
or nonabrasive
cleaner
and warm soapy water. Wipe
dry with a soft
nonabrasive
cloth.
* Stainless steel surfaces:
To maintain
your grill's high quality
appearance,
wash with mild detergent
and warm soapy water
and wipe dry with a soft cloth after each use. Baked-on
grease
deposits
may require the use of an abrasive
plastic cleaning
pad. Use only in direction
of brushed finish to avoid damage.
Do not use abrasive
pad on areas with graphics.
" Cooking surfaces:
If a bristle brush is used to clean any of
the grill cooking
surfaces, ensure no loose bristles remain on
cooking
surfaces prior to grilling.
It is not recommended
to
clean cooking
surfaces while grill is hot.
Publicidad
