Winix T810 Manual De Usuario

MODEL PART DIAGRAM
FRONT FRONT
Control Panel Control Panel
Front Panel
Front Panel
PACKAGE CONTENTS
PACKAGE CONTENTS
360º All-in-One 360º All-in-One
Unit
Unit
True HEPA Filter True HEPA Filter
WHERE TO USE
Allow 12 ~ 18 in. of space between TVs, radios, , humidifiers, and
other electronics
It can cause malfunction due to electromagnetic interference and
humidified water.
Place indoors away from direct sunlight
Direct exposure may cause product malfunction or failure.
Only place on hard, flat surfaces
Flimsy or slanted surfaces may result in abnormal noise and
vibrations.
12~18 in
12~18 in
12~18 in
12~18 in
Allow 12 ~ 18 in. from walls
For maximum air flow.
4-STAGE
AIR PURIFICATION
Air Purification means it
removes inanimate particles
INITIAL OPERATION
1. Turn the product upside down.
2. Grab the handle at the bottom of the
product, turn counter-clockwise, and pull
out the filter cover.
3. Remove the protective vinyl from the filter
installed inside the product.
4. Install the filter top side down into the
bottom of unit until it is fully inserted. The
top of the filter shows the opening and the
bottom of the filter is solid.
5. After installing the filter, turn the handle
clockwise to close the filter cover.
6. Return the product to an upright position
and resume normal operation.
MAINTENANCE
When to Replace Filters
Filter Indicator Light
360º All-in-One
True HEPA Filter
Check Filter
• When the Check Filter indicator LED is on, it is time to replace the All-in-One True HEPA Filter.
• Intervals between filter replacement may vary depending on environment.
REPLACING FILTERS
Resetting Filter Life:
After replacing the 360º All-in-One True HEPA Filter, use a small object such as
hear the beep. After the beep, the Filter Replacement Indicator will disappear.
The numerical pollution level value displayed may differ from the information provided by
official institutions depending on the indoor environment or the location of the product.
BLUE GREEN
0 ~ 35 36 ~ 55
*PM2.5
BACK BACK
Air Outlet Vent Air Outlet Vent
Handle
Handle
Smart Sensor
Smart Sensor
Power Plug Power Plug
User User
Manual Manual
PlasmaWave Technology Technology
Activated Carbon Filter Activated Carbon Filter
True HEPA Filter
True HEPA Filter
Fine Mesh Pre-Filter Fine Mesh Pre-Filter
When to Service When to Replace
Clean once every 14 days Lasts Approx. 12 months
1712-0118-00
ORANGE RED
56 ~ 150 150 ~ or higher
CONTROL PANEL
01
02
03
04
05
01. Filter Life / Filter Reset Button
• A quick press will show the remaining filter life:
indicated on the front display (F99 ~ F00).
• A long press of 10 seconds will reset the filter life indicator.
- Use when replacing the filters.
- Filter Reset Button can be used when the power is turned off.
- The filter life will be reset to 100%.
02. Light Mode Button
Use the light button to set the desired display brightness. The
display brightness cycles in the order of 100%
OFF. Other features remain unchanged.
03. Fan Speed Indicator Buttons
Indicates the current fan speed.
• Use the Fan Speed arrow buttons to set the desired fan
speed. Fan speeds cycle over in this sequence:
Auto, Low, Mdium, High, Turbo.
04. Auto Mode Button
The unit will default to Auto with PlasmaWave
first powered on.
• Auto Mode automatically adjusts fan speeds according to
your indoor air quality. The fan speed will adjust to low when
air quality is good, medium when fair, and to high when poor.
05. Power Button
Quality Indicator will cycle through Blue, Green, Amber and Red colors.
•
air quality in the environment before normal operation begins.
06. Light Sensor
Detects the amount of ambient light in the environment. When
in Auto Mode, the light sensor detects when to put the unit into
Sleep Mode.
07. Wi-Fi / Pairing Button
• A quick press will turn Wi-Fi on/off.
• A long press of 3 seconds will activate pairing mode.
• A Wi-Fi indicator will display on the front while Wi-Fi is active.
CLEANING CARE
Cleaning the Filters:
Clean with a vacuum or a soft brush.
• Only clean the Pre-Filter.
BOTTOM
• This filter CAN NOT be washed.
• Intervals between filter cleaning may vary
depending on the air quality.
Cleaning the Exterior & Interior:
Wipe with a soft damp cloth using room temperature
water. Afterwards, wipe it down with a clean dry cloth.
After turning the product upside down, remove the
filter cover and clean the interior with a vacuum
cleaner.
• For optimal performance, clean every 14 days.
N O T I C E
• When cleaning the unit, always unplug the power cord
first and then wait until the unit has cooled down.
• Never disassemble, repair, or modify this unit yourself.
• Do not use flammable sprays or liquid detergents.
• Do not allow children to clean or maintain the unit.
R
FILTER
• Before cleaning or maintaining, ensure unit is unplugged.
• Do not use benzene, alcohol, or other volatile fluids,
which may cause damage or discoloration.
UNIT SPECIFICATIONS
Model Name
Power Voltage
Power Rate
3
)
Verified Room Size
The exterior, design, and product specifications may be changed without prior notice to improve product performance.
Contact Winix for product related inquiries and customer service
• Dedicated Call Center: ☎ (877) 699-4649
• Website: www.winixamerica.com
To expedite service, please specify the model name and number, the nature of the problem, your contact
information, and your address.
06
07
08
13
03
09
08. Air Quality Indicator
Color coded LED light indicates one of four levels of Air Quality:
Red (poor), Amber (fair), Green (average) and Blue (good).
09. PlasmaWave ® Button
Enables or disables PlasmaWave
When the unit is running, you may hear a chirping or
buzzing sound. The sound is from particles passing through
®
PlasmaWave , it is normal and does not signify product failure.
Press the PlasmaWave
70% 30% to enable or disable this feature.
10. Mode Indicator
Indicates whether Auto & Fan Speed Mode is enabled or disabled.
11. Sleep Mode Indicator
® enabled when
Indicates whether Sleep Mode is enabled or disabled.
12. Wi-Fi Indicator
Indicates whether Wi-Fi Mode is enabled or disabled.
®
13. PlasmaWave Indicator
Indicates whether PlasmaWave
14. Filter Replacement Indicator
LED light indicates when it is time to change the filter.
15. Ultrafine Dust Density Indicator
• The LED Ultrafine Dust Density Indicator displays the quality
of air in your environment.
When the unit senses an air quality change, it automatically
adjusts the LED Indicator to display the respective air quality.
• LED Numeric Smart Sensor displays air quality measures
fine particles down to 2.5 microns.
How to disassemble and clean the smart sensor cover
1. Please use your finger to detach the cover of the
dust sensor.
2. Clean the lens and suction port of the dust sensor
with a cotton swab, and then use a dry cotton
swab to clean the dust sensor.
(Cleaning frequency: Once every two months)
3. Close the cover of the dust sensor until you hear
a clicking sound.
N O T I C E
• Do not clean the sensor with volatile substances such
as water, alcohol, or acetone.
If not cleaned regularly, the performance of the dust
sensor may deteriorate.
T810 Dimensions 11.3 in(W) x 11.3 in(D) x 20.4 in(H)
AC 120 V / 60 Hz Weight
Replacement
Filter
10 11 12
14
15
®
® Technology button when the unit is on
Low Medium High Turbo
® is enabled or disabled.
R