Publicidad
Idiomas disponibles
Idiomas disponibles
•
Do not cut vines and/or small under-brush.
•
Use extreme caution when cutting small size brush and
saplings because slender material may catch the saw chain
and be whipped toward you or pull you off balance.
Pruner Names and Terms
Bucking ‑ The process of cross-cutting a felled tree or log
•
into lengths.
Motor Brake (if equipped) ‑ A device used to stop the saw
•
chain when the trigger is released.
Pruner Powerhead ‑ A pruner without the saw chain and
•
guide bar.
Drive Sprocket or Sprocket ‑ The toothed part that drives
•
the saw chain.
Felling ‑ The process of cutting down a tree.
•
Felling Back Cut ‑ The final cut in a tree felling operation made
•
on the opposite side of the tree from the notching cut.
Front Handle ‑ The support handle located at or toward the
•
front of the pruner.
Front Hand Guard ‑ A structural barrier between the front
•
handle of a pruner and the guide bar, typically located close to
the hand position on the front handle.
Guide Bar ‑ A solid railed structure that supports and guides
•
the saw chain.
Scabbard/Guide Bar Cover ‑ Enclosure fitted over guide bar
•
to help prevent tooth contact when saw is not in use.
Kickback ‑ The backward or upward motion, or both of the
•
guide bar occurring when the saw chain near the nose of the
top area of the guide bar contacts any object such as a log or
branch, or when the wood closes in and pinches the saw chain
in the cut.
Kickback, Pinch ‑ The rapid pushback of the saw which can
•
occur when the wood closes in and pinches the moving saw
chain in the cut along the top of the guide bar.
Kickback, Rotational ‑ The rapid upward and backward
•
motion of the saw which can occur when the moving saw
chain near the upper portion of the tip of the guide bar
contacts an object, such as a log or branch.
Limbing ‑ Removing the branches from a fallen tree.
•
Low‑Kickback Chain ‑ A chain that complies with the
•
kickback performance requirements of ANSI B175.1–2012
(when tested on a representative sample of pruners).
Normal Cutting Position ‑ Those positions assumed in
•
performing the bucking and felling cuts.
Notching Undercut ‑ A notch cut in a tree that directs the
•
tree's fall.
Rear Handle ‑ The support handle located at or toward the
•
rear of the saw.
Reduced Kickback Guide Bar ‑ A guide bar which has been
•
demonstrated to reduce kickback significantly.
Replacement Saw Chain ‑ A chain that complies with
•
kickback performance requirements of ANSI B175.1–2012
when tested with specific pruners. It may not meet the ANSI
performance requirements when used with other saws.
Saw Chain ‑ A loop of chain having cutting teeth, that cut the
•
wood, and that is driven by the motor and is supported by the
guide bar.
Ribbed Bumper ‑ The ribs used when felling or bucking to
•
pivot the saw and maintain position while sawing.
Switch ‑ A device that when operated will complete or
•
interrupt an electrical power circuit to the motor of the pruner.
Switch Linkage ‑ The mechanism that transmits motion from
•
a trigger to the switch.
Switch Lockout ‑ A movable stop that prevents the
•
unintentional operation of the switch until manually actuated.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
•
Impairment of hearing.
•
Risk of personal injury due to flying particles.
•
Risk of burns due to accessories becoming hot
during operation.
•
Risk of personal injury due to prolonged use.
SAVE THESE INSTRUCTIONS
Chargers
D
WALT chargers require no adjustment and are designed to be
e
as easy as possible to operate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
i
your charger corresponds to that of your mains.
Your D
WALT charger is double insulated in
e
accordance with EN60335; therefore, no earth wire
is required.
If the supply cord is damaged, it must be replaced only by
D
WALT or an authorised service organisation.
e
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
•
Safely dispose of the old plug.
•
Connect the brown lead to the live terminal in the plug.
•
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3 A.
Using an Extension Cable
An extension cord should not be used unless absolutely necessary.
Use an approved extension cable suitable for the power input of
your charger (see Technical Data). The minimum conductor size is
1 mm
; the maximum length is 30 m.
2
When using a cable reel, always unwind the cable completely.
EnGLIsH
41
Publicidad
