Maintenance And Storage - Black and Decker SmartSelect BDPH1200 Manual De Instrucciones

that can be sprayed. Turning the flow knob clockwise
increases the flow of liquid. Turning the knob
counterclockwise decreases the flow of liquid. If
runs or drips do occur, have a dry paint brush on hand
to smooth them out.
f Turn the power unit off when not spraying for any
length of time.
CLEANING
Warning! Be sure to use appropriate protective gear.
f Do not use materials with a flashpoint higher than 60°C
(140°F). Flashpoint is the temperature that a fluid can
produce enough vapors to ignite (see coating supplier).
f Make sure clean up area is well ventilated and free of
flammable vapors.
f Always spray outdoors when spraying cleaning
solution through sprayer.
f Do not submerse power unit.
f Use drop cloths during pouring, mixing, and viscosity
testing of materials to be sprayed to protect your floors
and anything else in the spraying area that you wish to
remain untouched.
To begin cleaning:
f Turn the power unit off, unplug the cord and disconnect
air hose from sprayer.
f Unscrew the lid from the side of the canister and pour
any remainingliquid back into the original container
(Fig. M).
f Pour a small amount of the appropriate cleaning
solution into the canister (Fig. N).
a. Warm soapy water for water based materials.
b. Manufacturers recommended cleaning solution
for oil based materials.
f Screw on the canister back to the sprayer securely
and vigorously shake the sprayer.
f Unscrew the canister and properly dispose
of cleaning solution.
f Refill the canister with a small amount of new cleaning
solution (Fig. M). Screw on the canister back the sprayer.
► Reattach the air hose to the sprayer, plug in the cord
and turn on the power unit.
► Spray the cleaning solution through the sprayer onto
scrap material for 2 to 3 seconds (Fig. O).
► Turn the power unit off, unplug the cord and
disconnect air hose from sprayer.
► Unscrew the canister from the sprayer.
► Remove the o-ring (14), pickup tube (15), check valve
(16), and quick refill lid (12) from the sprayer. Clean
the parts with the cleaning brush in the appropriate
cleaning solution (Fig. P).
Note: When removing the check valve, twist the check
valve clockwise and then pull it out. (Fig. P insert)
► Unscrew the tip collar (4) and remove all the parts of
the spray nozzle (#3, #4, #5, #6, #7, #8) from the sprayer.
Remove the spray tip (9) from the sprayer (Fig. Q1).
Clean all parts with the cleaning brush in the
appropriate cleaning solution (Fig. Q, Fig. Q1).
Be sure to clean around check valve with brush
(Fig. Q insert).
► If using water based material, clean the sprayer by
running water through pickup tube inlet as shown in
Fig. R. If using oil based materials, clean pickup tube
inlet with the appropriate cleaning solution.
► Repeat until sprayer is completely clean.
► Dry all parts thoroughly.
► Properly dispose of cleaning solution.
► Place a drop of household oil into the inside
of the sprayer from the hole for assembling the
spray tip (Fig. S).
► Reassemble sprayer (Fig. T).
Note: Spray nozzle can only be assembled in one
direction that the notch of the nozzle (6) must align with the
skirt on spray unit housing (10). Refer to Fig. T1 for proper
assembly.
Note: The spray tip must be assembled in the sprayer with
the bumps on the spray tip in vertical direction
Note: Assemble the pickup tube (15) and check valve (16)
by firmly pushing them onto the inlet on the sprayer.
► Wrap the air hose around the power unit and put all
accessories back into place.

MAINTENANCE AND STORAGE

Use only mild soap and damp cloth to clean the power
unit. Never let any liquid get inside the power unit; never
immerse any part of the power unit into a liquid.
Important! To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (other than those
listed in this manual) should be performed by authorized
service centers or other qualified service personnel,
always using identical replacement parts.
The power unit contains 3 washable/reusable filters (25, 27,
30). Check the filter before and after each use. If dirty, wash
with warm water and allow to air dry before re-installing or
replace if necessary. (Fig. U2).
f To check the filter.
f Remove the filter cover (24) by squeezing the top and
bottom sides of the filter cover (24) and pulling the
cover off the power unit.
f Remove the air ventilation cover (31) with a tool to
lever open the cover off the power unit (FIG. U1).
f Remove the filter as shown in Fig.U2 and inspect.
Replace filter and filter cover.
Warning! Never operate the power unit without the
filter in place. Debris could be sucked in and interfere with
the function of the power unit.
ENGLISH • 33