Publicidad
Idiomas disponibles
Idiomas disponibles
„ Never let anyone use your chain saw who has not received
adequate instructions in its proper use. This applies to
rentals as well as privately owned saws.
„ Before you start the unit, make sure the saw chain is not
contacting any object.
„ Stop the chain saw before setting it down.
„ To avoid accidental starting, never carry the unit with your
finger on the switch trigger.
„ Maintain the unit with care. Keep the cutting edge sharp
and clean for best performance and to reduce the risk
of injury. Follow instructions for lubricating and changing
accessories.
„ Do not operate a chain saw with one hand! Use a firm
grip with thumbs and fingers encircling the chain saw
handles. Serious injury to the operator, helpers, bystand-
ers, or any combination of these persons may result
from one-handed operation. A chain saw is intended for
two-handed use.
„ Guard against electric shock – Avoid body contact with
grounded surfaces such as metal pipes and wire fences.
There is an increased risk of electric shock if your body
is grounded.
„ Do not operate a chain saw that is damaged, improperly
adjusted, or not completely and securely assembled.
Chain should slow to a stop when the switch trigger is
released. If the chain continues to turn after the switch
trigger has been released, have the unit serviced by an
authorized service center.
„ Check for damaged parts. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mount-
ing, and any other conditions that may affect its operation.
A guard or other part that is damaged should be properly
repaired or replaced by an authorized service center un-
less otherwise indicated elsewhere in this manual.
„ All chain saw service, other than the items listed in the op-
eration and maintenance sections, should be performed
by an authorized service center.
„ Always maintain a proper stance.
„ Do not use chain saw if switch does not turn it on and off.
Have switch replaced by an authorized service center.
„ Do not adapt your power head to a bow guide or use it to
power any attachments or devices not listed for the saw.
„ Disconnect chain saw from power supply when not in
use, before servicing, and when making adjustments and
changing attachments, such as saw chain and guard.
„ Do not cut vines and/or small underbrush.
„ Do not force the chain saw. The job can be performed
better and safer at the rate for which it was intended.
„ When clearing jammed material or servicing the
unit, make sure all power switches are off and
the battery pack is removed or disconnected.
Unexpected actuation of the chain saw while clearing
CHAIN SAW SAFETY WARNINGS
jammed material or servicing may result in serious per-
sonal injury.
„ Always use the right product for your application. The
chain saw should be used for cutting wood only. Never
use the chain saw to cut plastic, masonry or non-wood
building materials.
„ Store chain saw when not charging or when not in use.
Chain saw should be stored in a dry and high or locked
area out of the reach of children. When storing chain saw
place the scabbard on the bar and chain.
„ Use this product only with batteries and chargers listed in
tool/appliance/battery pack/charger correlation supple-
ment 987000-432.
„ Battery operated units do not have to be plugged into an
electrical outlet; therefore, they are always in operating
condition. Be aware of possible hazards even when unit
is not operating.
„ Remove the battery pack from the chain saw when not
charging and before cleaning, servicing, storing, removing
material from the unit, changing accessories such as the
bar and chain, or when not in use.
„ Never use water or any liquids to clean or rinse off your
product and do not expose the product to rain or wet
conditions. Store indoors in a dry area. Corrosive liquids,
water, and chemicals can enter the product's electronic
components and/or battery compartment and damage
electronic components and/or the battery pack, which
can result in a short circuit, increased risk of fire, and seri-
ous personal injury. Remove any buildup of dirt and debris
by wiping the product clean with a dry cloth occasionally.
KICKBACK
See Figures 2 - 4.
WARNING:
Kickback may occur when the moving chain contacts an
object at the upper portion of the tip of the guide bar or
when the wood closes in and pinches the saw chain in the
cut. Contact at the upper portion of the tip of the guide
bar can cause the chain to dig into the object and stop the
chain for an instant. The result is a lightning fast, reverse
reaction which kicks the guide bar up and back toward
the operator. If the saw chain is pinched along the top of
the guide bar, the guide bar can be driven rapidly back
toward the operator. Either of these reactions can cause
loss of saw control which can result in serious injury. Do
not rely exclusively upon the safety devices built into the
saw. As a chain saw user, you should take several steps
to keep your cutting jobs free from accident or injury.
The following precautions should be followed to mini-
mize kickback:
• Always grip the saw firmly with both hands. Hold the
saw firmly with both hands when the unit is running.
5 - English
Publicidad
