Scheppach HS110 Traduccion Del Manual De Instrucciones Originale página 40

• Before connecting the machine, check that the data
on the type plate matches those of the mains sys-
tem.
• The machine must only be connected to a properly
installed safety socket which is protected by a fuse
of at least 16A.
8. Assembly
m Warning! Risk of injury!
Improper installation of the circular table saw may re-
sult in serious injury.
Before commissioning, properly and completely install
the circular table saw, including all covers and safety
devices.
Never plug the mains plug into the power outlet before
completing the installation.
If connections are secured with a hexagon screw, nut,
spring washer and washer, the washer and spring
washer must be fitted under the hexagon screw. The
spring washer always lies directly on the (inner) hexa-
gon screw or nut.
Hexagon screws must each be inserted from outside
inwards, and the connections must be secured from
the inside with nuts. During assembly nuts and screws
must only be tightened until hand-tight, so that they
cannot fall out. If you tighten the nuts and screws fully
before final assembly, the circular table saw cannot be
erected in a correct and stable manner.
8.1 Assembling the frame and table width extender
(Fig. 4-10)
1. Turn circular table saw upside down and place on
the floor.
2. Fasten the table width extension (6) loosely onto
the saw table (1) with the hexagonal bolts (a), the
washers (c) and the nuts (e) (fig. 6).
3. The four legs (19) are screwed to the housing to-
gether with the table supports (24) (fig. 7).
4. Fasten the table supports (24) loosely to the table
width extensions (6) with the hexagonal bolts (a),
the washers (c) and the nuts (e). Loosely tighten
the legs (19) and the table supports (24) onto the
housing of the circular table saw with the hexago-
nal bolts (a).
5. Now loosely screw the four central struts (20a,20b)
with the legs (19) using the carriage bolts (b),
washer (c), spring washer (d) and nuts (e). (Fig. 8)
40 | GB
6. Screw the stand brackets (22) to the holes in the
rear stand legs (19). Assembly material: 2 carriage
bolts (b), washers (c), spring washers (d) and nuts
(e). (Fig. 9)
ATTENTION: Both stand brackets (22) must be
attached to the rear of the machine at the fixing
points (23). (Fig. 9)
7. Align the table width and length extension lush
with the saw table.
8. Next, tighten all the screws of the legs (19) and the
table width extender (6).
9. Now attach the rubber feet (21) to the legs (19)
(Fig. 10).
10. Place the table circular saw on the base frame (11).
8.2 Insert guide rail (Fig. 11+12)
1. Mount the carriage bolts (b) in the holes provided
in the worktable and the table extensions (6) by
securing them from behind with the flange nuts (e).
2. Loosely tighten the flange nuts (e).
3. Connect both guide rails (15, 15a).
4. Slide the connected reails over the guide groove
on the back over the carriage bolts (b) until they
are centred on the table surface.
8.3 Aligning the guide rail (Fig. 11+12)
1. Turn the saw blade out of the sawing table at max-
imum by turning the crank (10) clockwise as far as
it will go.
2. Position the rip fence (14) with the cam lever (13)
open on the guide rails (15) on the sawing table
and fix it in the 0-position by pushing the cam lever
(13) down completely.
3. Slide the connected guide rails to the left until the
rip fence is at the outer right side of the saw blade.
4. Then tighten the flange nuts (e) to fix this setting.
5. No fit the end caps (15b) on both sides of the rail.
8.4 Fitting/removing the saw blade guard
(fig. 13+14)
1. Place the saw blade guard (2) on the riving knife
(3) from above, so that the screw with the knurled
nut (27) sits firmly in the hole of the riving knife (3).
Attention! To be able to place the saw blade guard
(2) on the riving knife (3), the screw with knurled
nut (27) must be moved so that the smaller shaft
diameter fits into the slotted hole in the riving knife
(3).
www.scheppach.com