Scheppach HS110 Traduccion Del Manual De Instrucciones Originale página 41

2. Do not tighten the knurled nut too much. The saw
blade guard (2) must remain free to move.
Attention! When tightening, make sure that the
larger shaft diameter of the screw fits into the hole
in the riving knife (3).
3. Disassembly takes place in reverse order.
m CAUTION: Before you start sawing, the saw balde
guard (2) has to be lowered onto the item being sawn.
After fitting, check that the saw blade guard (2) is func-
tioning properly. Lift the saw blade guard and then
release it. The saw blade guard should automatically
move back to its starting position.
8.5 Mounting / adjusting the riving knife
Caution! Remove the mains plug! The setting of
the saw blade (4) must be checked whenever a
blade has been replaced.
1. Adjust the saw blade (4) to a max. cutting depth,
move to the 0° position and lock in place.
2. Dismantle the saw blade guard (2) (not during ini-
tial assembly).
3. Release the two countersunk screws of the table
insert (25) and remove the table insert (5).
4. Loosen the fixing srew of the riving knife (26). (use
the open-ended spanner AF8 supplied).
5. Push the riving knife (3) upwards.
6. The distance between the saw blade (4) and riving
knife (3) should be between 3 mm and max. 5 mm,
(Figure. 15)
7. Retighten the fixing screw of the riving knife (26)
and mount the table insert (5).
8. Mount the saw blade guard (2) with the screw and
knurled nut and washer (27).
8.6 Connect the suction device (Fig. 2)
1. Attach a suction hose to the suction adapter (16).
If necessary, secure the suction hose with a hose
clamp to prevent it from slipping off the suction
adapter (16).
2. A household vacuum cleaner is not suitable as
a suction device. Use a multi-purpose vacuum
cleaner or a swarf extraction machine.
9. Operation
m Attention!
Always make sure the product is fully assembled
before commissioning!
9.1 Switchin on and off (Fig. 3)
• The saw can be switched on by pressing the green
"I" button on the on/off switch. Before you start saw-
ing, wait until the saw blade has reached its maxi-
mum speed.
• To switch the saw off again, press the red "0" button
on the on/off switch.
9.2 Adjusting the Cutting Depth (Fig. 1+3)
The saw blade (4) can be (continuously) adjusted to the
required cutting depth by turning the hand wheel for the
height adjustment (9)
• Anticlockwise: reduces the cutting depth
• Clockwise: increases the cutting depth
Check the adjustment by means of a test cut.
9.3 Angle adjustment (Fig. 1, 17, 21, 22)
With the table circular saw it is possible to make bevel
cuts to the left at an angle of 0° to 45° to the stop rail
(14).
m Before making every cut, check that no collision can
occur between stop rail (30), transverse stop (31) and
saw blade (4).
1. Release the locking handle (7).
2. Set the desired angle on the scale by pushing in
and turning the hand wheel (9).
3. Lock the locking handle (7) in the desired angular
position.
9.4 Working with the parallel Stop (Fig. 17-23)
9.4.1 Adjusting the stop height (Fig. 17+18)
• The stop rail (30) of the parallel stop (14) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (30) must be used for thick material
(workpiece thickness exceeding 25 mm) and for thin
material (workpiece thickness below 25 mm).
9.4.2 Turning the stop rail (Fig. 17)
1. In order to turn the stop rail (30), irst release the
two knurled nuts(i).
2. Now the stop rail (30) can be pulled off the guide
rail (14) and pushed back over it again with the
groove.
www.scheppach.com GB | 41