Descargar Imprimir esta página

EINHELL TP-DWS 18/225 Li BL Manual De Instrucciones Original página 19

Lijadora para paredes en seco inalámbrica

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 87
6. Operation
6.1 On/Off switch (Fig. 9 / item 1)
Switching on:
Press the release/locking button (2) and the On/
Off switch (1) at the same time.
Locking:
Release the On/Off switch (1) while pressing the
release/locking button (2).
Switching off :
Press the On/Off switch (1) briefl y and then re-
lease it.
6.2 Speed controller (Fig. 9/Item 3)
You can preselect the speed by pressing the
speed controller (3).
Plus direction:
Higher speed
Minus direction:
Lower speed
6.3 Working close to edges
(Fig. 10-11 / item 6)
To work close to edges and remove the side part
(6) as shown in Fig. 10.
Now you can run the tool straight along the edge
of a wall. (See Fig. 11)
6.4 Working with the drywall power sander
Place the whole surface area of the sanding
head on the material.
Switch on the machine and move it with
gentle pressure over the „workpiece", making
circular or transverse and linear movements.
Use a coarse grit for coarse sanding and a
finer grit for finish sanding. You can find the
best grit size for the job by carrying out san-
ding tests.
Caution!
The dusts which are formed while the equipment
is being used may be a health hazard:
Always wear safety goggles and a dust mask
during sanding work.
All persons who work with the equipment or
enter the workplace must wear a protective
dust mask.
Eating, drinking and smoking are prohibited
at the workplace.
Paints containing lead are not allowed to be
used!
Anl_TP_DWS_18_225_Li_BL_SPK13.indb 19
Anl_TP_DWS_18_225_Li_BL_SPK13.indb 19
GB
6.5 Releasing the sanding disk (Fig. 8/Item 7)
The sanding disk release (7) can be used to ren-
der the sanding disk (14) movable in axial direc-
tion or to fasten it so that it cannot move.
If you pull out the sanding disk release (7) the
sanding disk (14) will be rendered movable.
This is an advantage when sanding soft
materials (plaster or similar) because the san-
ding disk (14) will then yield under excessive
pressure and leave no marks.
If you push in the sanding disk release (7) the
sanding disk (14) cannot move and will yield
only at the foamed plastic.
This is an advantage when sanding hard sur-
faces (concrete, wood or similar) because a
higher removal rate is then achieved.
7. Cleaning, maintenance and
ordering spare parts
Hazard!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
We recommend that you clean the device
immediately each time you have finished
using it.
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 19 -
27.06.2023 15:15:19
27.06.2023 15:15:19

Publicidad

loading

Este manual también es adecuado para:

Tp-dws 18/225 li bl solo42.599.95