Metabo TBP 6200/8 Inox Manual Original página 9

Do not touch the plug with wet hands! Always pull
on the plug and not the power cable to disconnect it.
Connect it only to an earthed outlet that is properly
installed, earthed and tested.
National installation specifications must be
observed.
The earthed outlet or the plug connection with an
extension cable must be located in a flood-proof
area and protected from water.
Extension cables must have sufficient conductor
cross sections. Cable reels must be fully unrolled.
Do not buckle, squeeze, drag or drive over the
power cable or extension cables; protect them from
sharp edges, oil and heat.
Place extension cable so that it can not get into the
fluid to be pumped.
Unplug power cable;
- before any work on the pump;
- if there are people in the swimming pool or garden
pond.
The electrical connections must not be under water
and must be located in a flood-proof area. The
connections must be splash-proof for outdoor use.
4.4 Danger due to pump defects or
malfunctions!
Check the pump for possible damage - especially
the mains cable, mains plug and electrical
components before each use. Risk of fatal electric
shock!
A damaged pump must only be reused after it has
been correctly repaired.
Do not attempt to repair the pump yourself! Only
professionals are allowed to carry out repairs on
pumps.
To prevent water damage, such as flooded
rooms, caused by deficiencies or faults on the
device:
- Provide appropriate safety measures, e.g. alarm
device or collection tank with monitoring
The manufacturer is not liable for any damage
caused by:
- Improper use of the pump.
- Failure to operate and store the pump in a frost-
free environment.
- Unauthorised modifications being made to the
pump. Repairs to pumps must only be carried out
by qualified electricians!
- Use of spare parts which have not been tested
and approved by the manufacturer.
- Use of unsuitable installation materials (fittings,
connection lines etc.).
When using universal swivel couplings (bayonet
couplings), only use versions with an additional
securing ring to ensure safe sealing.
Contamination of the fluid could be caused by
lubricant leakage.
5. Overview
See page 2.
1 Pressure connection
2 Eyelet (for securing the rope)
3 Screws (for securing the stand)
4 Machine stand
5 Check valve (prevents the water from flowing
back through the pump)
6 Stainless steel filter
7 Screws (for securing the stainless steel filter)
6. Initial Operation
6.1 Mounting the stand
If the pump is placed on the ground, the stand
must be fitted to keep the pump away from any
deposited sand or dirt.
See page 2, fig. B.
- Attach the stand (4) from below.
- Fix the stand (4) with both screws (3).
6.2 Connecting the discharge line
Screw the pressure line to the pressure connection
(1) using an adapter.
The pressure line and adapter are not included in
the scope of delivery. Follow the manufacturer's
installation instructions.
For optimum delivery performance: use suitable
adapters and pressure lines that fit the pressure
connection thread (1) without reducing the internal
diameter unnecessarily.
All discharge line components must be pressure-
resistant and installed correctly.
Suitable installation materials:
- pressure-resistant (min. 10 bar)
- heat-resistant (min. 100°C).
The discharge line can burst during operation
if non-pressure-resistant components are
installed or they are assembled incorrectly. Injuries
are possible if highly pressurised fluids are ejected!
6.3 Fastening the rope
Do not lift the pump by the mains cable or the
pressure hose. These are not designed for
tensile load.
Attach a sturdy rope to the eyelet (2) to lower the
pump into the water.
6.4 Installation
Do not exceed the maximum permitted
submersion depth (see chapter 13. technical
data).
See page 2, fig. E.
a) Without stand attached (4): The pump must be
operated suspended from the rope at least 20 cm
(7 7/8") above the ground to keep the pump clear of
deposited sand or dirt.
b) With stand attached (4): The pump may be
placed on the ground.
1. Lower the pump by the rope into a well or shaft.
The mains cable and pressure hose must not be
subjected to tensile stress.
ENGLISH en
9