Publicidad
Idiomas disponibles
Idiomas disponibles
3. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and
a mild detergent in warm water.
To avoid damaging wooden tines and trim pieces, wipe
them off with a clean sponge or soft cloth and warm water.
Do not use detergent or immerse the entire rack into water
when cleaning.
Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, fl ammable fl uids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior and
door liners or gaskets. Do not use paper towels, scouring
pads, or other harsh cleaning tools. These can scratch or
damage materials.
To help remove odors, you can wash interior walls with a
mixture of warm water and baking soda (2 tbs to 1 qt [26 g
to 0.95 L] of water).
4. Wash stainless steel and painted metal exteriors with a
clean sponge or soft cloth and a mild detergent in warm
water. Do not use abrasive or harsh cleaners, or cleaners
containing chlorine. These can scratch or damage
materials. Dry immediately with a soft, dry cloth to absorb
any remaining water.
NOTE: To keep your stainless steel refrigerator looking like
new and to remove minor scuffs or marks, it is
recommended that you use the manufacturer's approved
Stainless Steel Cleaner and Polish.
IMPORTANT:
This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry immediately with a soft, dry
cloth to absorb any remaining water.
5. Replace the shelves and bins.
Condenser cleaning
Explosion Hazard
Risk of fire or explosion due to puncture of refrigerant
tubing.
Follow handling instructions carefully.
Flammable refrigerant used.
1. Remove the base grille to access condenser for cleaning.
Refer "Removing Base Grille" section.
2. Clean the condenser coils regularly. They are located
behind the base grille. Coils may need to be cleaned as
often as every other month. This may help save energy.
10
Manual W11515231B -SD-Ingles.indd 10
Manual W11515231B -SD-Ingles.indd 10
Removing Base Grille
You must remove the base grille to access the condenser
coils for cleaning.
To remove the base grille:
1. Open the refrigerator door.
A. Screws
2. Using a Phillips screwdriver, remove the two screws.
3. Remove the base grille.
To replace the base grille:
1. Open the refrigerator door.
2. Position the base grille so that both tabs align and the base
grille snaps into place. Replace two screws. Tighten the
screws.
Vacation Care
If you choose to turn the refrigerator off before you leave,
follow these steps.
1. Remove all food from the refrigerator.
2. Unplug the refrigerator.
3. Clean the refrigerator. Refer "Cleaning" section.
4. Tape a rubber or wood block to the top of the door to prop
it open far enough for air to get in. This stops odor and
mold from building up.
Moving Care
When you are moving your refrigerator to a new home, follow
these steps to prepare it for the move.
1. Remove all food from the refrigerator.
2. Unplug the refrigerator.
3. Clean, wipe, and dry it thoroughly.
4. Take out all removable parts, wrap them well, and tape
them together so they don't shift and rattle during the
move.
5. Tape the doors shut and tape the power cord to the
refrigerator.
When you get to your new home, put everything back and
refer to the "Installation Instructions" section.
A
02/02/21 15:14
02/02/21 15:14
Publicidad
