Lutron MACL-L3S25 Guía De Instalación Rápida

Quick Install Guide
How-to videos
l u t ro n . c o m / d u a l w i r i n g
MACL-L3S25 / MACL-L3T251
Maximum load ratings
75 W
LED / CFL
Dimmer
CFL
LED
LFCA
DEL
AFC
2.5 A
Switch /
Fan
Timer
and / or light
Please read before installing
English
WARNING: SHOCK HAZARD. May result in serious injury or death.
Turn off power at circuit breaker or fuse before installing.
Before Removing the Old Switch:
1. Place a single tag (electrical tape, for example) on the wire that
is connected to the Line / Hot side of the switch (the side with
the breakoff fin).
2. Place two tags on the wire from the load that you want to
connect to the timer or switch.
Identify side with breakoff fin
Tag
For advanced programming instructions,
please see Lutron Application Note #806
on www.lutron.com/DualFeatures
AFTER INSTALLATION: Adjust dimming range (set low-end trim)
Hold and until an indicator
A
T
light (IL) blinks on the dimmer.
IL
T
On
60
45
30
15
10
5
MACL-L3T251 only
Timer LEDs
• Orange LEDs indicate timer duration
or remaining time in minutes.
• Top LED labeled On has no time limit.
• Bottom LED blinks rapidly to indicate
one minute of time remaining.
Limited Warranty: www.lutron.com/warranty
©2022-2023 Lutron Electronics Co., Inc.
Lutron and LED+ are trademarks or registered trademarks of Lutron Electronics Co., Inc., in the U.S. and other countries.
The YouTube icon is a trademark of Google LLC.
Receive an Extended Warranty: www.lutron.com/CLregistration
24 / 7 Support: 1.844.LUTRON1 (USA / Canada)
Install with
confidence
Use included diagrams
or visit our website for
step-by-step instructions.
Ganging
Remove side sections if
mounting 2 or more devices side
300 W
Incand. / Hal. by side. No derating is required
when ganging this product.
INSTALL WITH CONFIDENCE
VIDEO & STEP-BY-STEP INSTRUCTIONS VIDEO & STEP-BY-STEP INSTRUC
lutron.com/dualwiring
B
Use or to
change timeout
On
60
45
30
15
10
5
LED + Dimmer
Keep
Remove
Bend back
and forth
Connect
MACL-L3T251 shown
Dimmer
Timer / Switch
Use or to improve
lowest dimming level.
OR
On
60
45
30
15
10
Troubleshooting
5
Symptoms
Product does not work
OR
Load flickers or
performs poorly
For more troubleshooting tips, please see www.lutron.com/support
®
120 V~ 60 Hz
Find the right LED
lutron.com/LEDfinder
Important Notes
1. Only use dimmer with permanently installed incandescent
or dimmable LED fixtures. To avoid overheating and possible
damage to other equipment, do not use to control receptacles,
fluorescent lighting fixtures, low-voltage lighting fixtures,
magnetic transformer loads, motor-driven appliances, or
transformer-supplied appliances.
2. Use switch to control any permanently installed lighting or fan
load. Switch is rated for fan and lighting loads up to 2.5 A.
3. Install in accordance with all national and local electrical codes.
4. When no "grounding means" exists in wallbox, the 2011
National Electrical CodeR (NECR) allows a control to be installed
as a replacement if 1) a nonmetallic, noncombustible faceplate
is used with non-metallic attachment screws or 2) the circuit
is protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or remove
green wire before screwing control into wallbox and use an
appropriate faceplate such as Claro or Satin Colors series
wallplates by Lutron.
5. For indoor use only between 32 °F and 104 °F (0 °C and
40 °C).
6. Clean dimmers with a soft damp cloth only. Do not use any
chemical cleaners.
7. Install per Lutron's torque guidelines at lutron.com/torque
TIONS
Red - Dimmer
circuit
Yellow - Timer
or switch circuit
On
60
45
Screw Terminal
30
15
10
5
Tag
Line / Hot
Green
Press
C
T
low-end trim mode.
On
60
45
30
15
10
5
Probable cause and action
Verify a working load is connected to
the dimmer
Verify bulb is on the compatible list
(see lutron.com/LEDfinder)
Adjust dimming range (see above)
P/N 0302118 REV A
+1.888.235.2910 (Mexico)
Tags
Ground
(green or bare)
to save and exit
T