DeWalt DXFP845101 Manual De Instrucciones página 6

English
WARNING: The fall arrest system MUST ONLY be connected to the back attachment element on the harness
provided for the purpose ("D" ring or webbing attachment extension) or to the chest anchorage points
("webbing link" or "D" link. The D-rings on the belt and the ventral anchorage point must only be used for the
attachment of a work positioning or retaining system and never with a fall arrest system.
WARNING: During use, check regularly the adjustment and/or attachment points.
WARNING: D WALT Anchors are designed to provide complete attachment system to the user in the event of
E
a fall. These attachment systems must be connected to proper body support and connecting facility. These
Anchors are meant to hold the victim of fall until the rescue operation is performed, so it is important that the
whole system must has all the essential components before being used. The whole fall arrest system must be
used by a trained/Authorized person. It is advisable to make a checklist of the essential components according to
one's use before going for work.
14) INSTRUCTIONS BEFORE USE
• It is vital that the user must be physically
and mentally fit for a proper and safe use of
this equipment in normal and emergency
situations. A physician's approval is must for
the user to state their medical records clear, so
that it doesn't affect the proper and safe use
of this equipment in normal and emergency
situations.
• Training as per the requirement of OSHA 29
CFR 1910.66 for safe usage of the system and
its components is compulsory for the user
prior to use of a personal fall arrest system.
• Personal fall arrest or restraint systems
complying with ANSI/OSHA must only be used
with this equipment. The strength capability
of at least 5,000-lbf (22kN) in the absence
of certification is must for the anchorage to
support a static load, applied in the directions
permitted by the system.
• It is important for the user to be equipped with
resource to limit the maximum dynamic forces
ILLUSTRATION OF CONCRETE ANCHOR
PIPE
FERRULE
CAP
Minimum
Product Model Description Breaking
System
UFA30090 Concrete Anchor 5000 lbs / 23 kN
8
exerted while having a fall to a maximum of
8 kN (1800-lbf). Whereas, for the European
regulation, the force must not exceed 6 kN
(1350-lbf).
• An engineer's or any other qualified person's
approval is must for the use of this product
to be compatible with any and all structural
& operational characteristics of the selected
installation location and system to be
connected to this anchorage connector.
• A thorough inspection for wear, damage and
other deterioration is must before using the
anchorage connector. If found defective, it
should be removed immediately from service
following the requirements of OSHA 29 CFR
1910.66 and 1926.502.
• Alteration or modification of this product is
prohibited.
• The installation/usage should never be done
without being properly trained by a competent
person" as defined by OSHA 29 CFR 1926.32(f).
POKE PIN WITH WIRE ASSEMBLE
ALUMINIUM HOLDER
CABLE GUIDE
WASHER
SPRING
FERRULE
WIRE CABLE
2.57" (65.4 mm) 1.57" (40.0 mm)
LABEL
Material of Construction Complying Norm
Cable: Galvanized Steel
ANSI Z359.18-2017
Type A
Clamping Jaws: Stainless Steel
INSTRUCTIONS FOR INSTALLATION OF CONCRETE ANCHOR
Squeeze the trigger
The Anchor may be attached to the structure by pulling on the spring loaded trigger component.
STEP 1:
A diameter hole of 0.75" (19mm) with minimum
deepness of 3.5" (89mm) is to be drilled ensuring it
to be straight and perpendicular to the surface. The
drilled hole must have a uniform diameter with no
trace of peaks and valleys on the inner wall. Clean the
drilled hole by blowing compressed air.
STEP 2:
Put your thumb inside the anchor loop and the
first two fingers around the trigger while placing
the anchor. Also until the trigger and spring fully
compresses, squeeze the fingers and thumb together.
To lock the anchor, release the trigger after inserting
it in the hole at least 3" (76mm) deep.
STEP 3:
Now the eye of the anchor can be used as anchorage
point. Connect the lanyard with the anchor. Now the
anchor is ready to use.
CLAMPING JAW
English
Release the trigger
STEP 1
STEP 2
STEP 3
9