Descargar Imprimir esta página

DeWalt DXFP845101 Manual De Instrucciones página 8

Publicidad

Idiomas disponibles

Idiomas disponibles

English
LIMITED REMEDY:
At D
WALTs sole discretion D
WALT would repair
e
e
or replace the defective equipment once a
written notice is received. The right to returning
of defective item to plant for prior inspection
before taking any action is reserved solely by
D
WALT. Equipment being damaged by wear
e
abuse, damage in transit, failure to maintain
the product or any other damage beyond the
repairing ability of D
WALT is not covered
e
under the warranty. D
WALT also holds the sole
e
right to judge product condition and warranty
options. This warranty applies only to original
purchaser and is the only warranty applicable to
this product. For any assistance, kindly contact
D
WALT Technical Service Department.
e
TWO-YEAR WARRANTY – FALL PROTECTION PRODUCTS:
THE FOLLOWING IS MADE IN LIEU OF ALL WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, INCLUDING THE
IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF DFP SAFETY CORPORATION FALL PROTECTION
PRODUCTS OR PARTS. THIS WARRANTY IS NOT ASSIGNABLE OR TRANSFERABLE. DFP SAFETY CORPORATION MAKES
NO WARRANTY TO ANYONE ELSE, INCLUDING OTHER PURCHASERS AND/OR USERS, AND NONE SHALL BE IMPLIED.
Except as otherwise provided in this warranty, DFP Safety Corporation Fall Protection Products are warranted against
defects in materials and workmanship for two years from the date of purchase.
LIMITED REMEDY: The sole and exclusive remedy for any DFP Safety Corporation product found to be defective in
materials and workmanship is repair or replacement, at the sole option of DFP Safety Corporation, or its authorized
warranty service providers. If this exclusive remedy is deemed to have failed of its essential purpose, DFP Safety
Corporation's liability shall not exceed the purchase price of the DFP Safety Corporation product.
LIMITATION OF LIABILITY: In no event will DFP Safety Corporation be liable for any direct, indirect, special, incidental,
punitive or consequential damages (including lost profit) whether based on warranty, contract, tort, or any other legal
theory.
This warranty does not cover any DFP Safety Corporation product that has been abused, altered, worn out,
contaminated, rusted, excessively heated, ground, damaged due to improper loading, used for a purpose other than
that for which it was intended, or used in a manner inconsistent with DFP Safety Corporation's instructions regarding
use.
The existence of a defect in materials or workmanship shall be determined by DFP Safety Corporation in
accordance with procedures established by DFP Safety Corporation. No one is authorized to make any statement or
representation altering the terms of this warranty.
ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE OF THIS
DOCUMENT.
This writing supersedes all prior oral or written agreements or representations and excludes all warranties not set
forth herein.
12
LIFESPAN:
The lifespan of any component of a personal fall
arrest system (PFAS) is dependent upon its level
of use, the environment in which it is used and
how it is maintained. Any part of the PFAS that
passes daily inspection by an Authorized person
or periodic (annual or semiannual) inspection
by a Competent person, can stay in use. Once it
fails visual inspection it must be removed from
service.
DISCLAIMER:
Prior to use, the end user, must read and
understand the manufacturer's instructions
supplied with this product at the time of
shipment and seek training from their
employer's trained personnel on the proper
usage of the product. Manufacturer is not liable
or responsible for any loss, damage or injury
caused or incurred by any person on grounds of
improper usage or installation of this product.
EQUIPMENT RECORD
Product:
Model and type/identification
Trade name
Manufacturer
Address
Purchase date
Year of manufacture
Other relevant information (e.g. Document number)
PERIODIC EXAMINATION AND REPAIR HISTORY
Reason for entry
Defects noted, repair
(periodic examination
Date
carried out and other
or repair)
relevant information
English
Identification number
Tel, fax, email
Date first put into use
Periodic
Name and signature
examination
of competent user
next due date
13

Publicidad

loading