EINHELL FREELEXO LCD BT Serie Manual De Instrucciones Original página 40

sensor is "On". You can activate or deactivate
the rain sensor (5) and set its delay time. The
delay time defines how long the robot lawn
mower continues to remain in the charging
station (19) after the rain sensor (5) has dried.
The standard setting for the delay time is 2
hours. Using the navigation buttons (56), go
to the setting that you require. After this, con-
firm the settings you have made by pressing
the "OK" button (54). Confirm the message
"Save changes?" with the "OK" button (54)
or press the back button (55) to discard the
change.
•
Leaving the station
You can set how far and where the robot lawn
mower travels when it reverses out of the
charging station (19). First the robot lawn mo-
wer reverses the set distance before it turns
into the area to be mowed or towards its star-
ting point. Make sure that the set reversing di-
stance does not cause the robot lawn mower
to leave the area to be mowed.
•
Language
Using the navigation buttons (56), go to the
language that you require. After this, confirm
the settings you have made by pressing the
"OK" button (54). Confirm the message "Save
changes?" with the "OK" button (54) or press
the back button (55) to discard the change.
•
Multi-starting point
Where gardens have lots of angles, the robot
lawn mower may have problems reaching
every part of the lawn and mowing it comple-
tely. In this case you can select several star-
ting points on the perimeter wire (18). This will
enable the robot lawn mower to get to even
those parts of your garden that are difficult to
reach. The robot lawn mower will run the se-
lected distance along the perimeter wire (18)
and then start mowing in this part of the gar-
den (Fig. 9b). Use the navigation buttons (56)
to go to the point that you wish to change and
enter the distance and frequency accordingly.
The charging station (19) is automatically
defined as starting point 1. The two other st-
arting points can be selected as you wish. For
this you must measure the distance between
the charging station (19) and the starting
point in clockwise direction along the perime-
ter wire (18). With the frequency setting you
decide how often the robot lawn mower starts
its work from the charging station (19) or from
the respective starting points.
•
Information
This provides you with information about the
Anl_FREELEXO_LCD_BT_SPK13.indb 40 Anl_FREELEXO_LCD_BT_SPK13.indb 40
GB
current software version of your robot lawn
mower
Mowing time settings
•
Operating time
This provides you with information about the
current settings of the operating times of your
robot lawn mower
•
Mowing edges
For a tidy lawn edge you can activate the
„Edge mowing" setting. You can also set the
lawn mowing frequency, i.e. the rhythm in
which you want the edge of the lawn to be
mowed at the beginning of the work window.
In the standard setting the robot lawn mower
will begin work on all 7 work days by first
mowing along the entire perimeter wire. In
addition, the robot lawn mower mows on the
way to the charging station at the end of the
daily mowing interval, if the charge level of
the rechargeable battery is over 70%.
•
Fault memory
This provides you with information about the
most recent fault messages of your robot
lawn mower.
•
Mower statistics
This provides you with information about a
range of mower statistics.
Changing the PIN
You can change the PIN for the robot lawn mo-
wer and use your own personal PIN. To do so,
proceed as described in the chapter "Locking
mechanism / PIN". Important! Make a note of the
new PIN.
6.6 Control of the robot lawn mower
Starting procedure
1. Unlock the control panel (2).
2. Press the "START" button (52) fi rst.
3. Close the display cover (22).
The robot lawn mower will now operate in ac-
cordance with the mowing time setting. The batte-
ry charge level is monitored during the work time
and displayed on the LCD-display (50). Whenever
the battery charge level drops to 30%, the robot
lawn mower automatically returns to the charging
station (19).
Stopping mowing
1. To bring the robot lawn mower to an immedia-
te stop, press the STOP button (3).
2. Unlock the control panel (2).
- 40 -
16.11.2023 10:09:19 16.11.2023 10:09:19