Invacare Aquatec 90000 Manual Del Usuario página 5

• Armrest (2x), (for version with armrest)
• User manual
6 cm, with and without Armrest (Fig. 1c, 1d)
• Corpus, 6 cm
• Lid
• Base incl. 2x clips
• Screw (2x)
• Plastic nut (2x)
• Height adapter
• Plug (2x) (for version without armrest)
• Armrest (2x), (for version with armrest)
• User manual
10 cm, with and without Armrest (Fig. 1e, 1f)
• Corpus, 10 cm
• Lid
• Base incl. 2x clips
• Screw (2x)
• Plastic nut (2x)
• Height adapter (2x)
• Plug (2x) (for version without armrest)
• Armrest (2x), (for version with armrest)
• User manual
4 Setup (Fig. 2a – 8)
CAUTION!
Risk of Pinching
– Take care during assembly.
Installing the Raised Toilet Seat (Fig. 2a – 8)
1. Slide the screws in the designated slot in the base on
both sides. Place the base and the height adapter(s) (if
applicable) on your toilet as shown on the image. (See
table) Tighten the plastic nut.
Height 2 cm Fig. 2a
Height 6 cm Fig. 2b
Height 10 cm Fig. 2c
2. Place the corpus by holding it upright and fixing it to
the base. (Fig. 3)
3. Loosen the plastic nuts, align the raised toilet seat
centrally to your toilet. Close the plastic nuts. (Fig. 4)
4. If your product is without armrests install the plugs on
both sides. (Fig. 5)
5. Clip on the lid. (Fig. 8)
To dismount the raised toilet seat reverse step 2 and
1.
Installing the Armrests (if applicable) (Fig. 6, 7)
1. Open the red clip by releasing the upper end of the clip
C and then the pin B of the red clip A. (Fig. 7) Then
install the armrests and close the red clip. (Fig. 6)
Ensure that the red clips A engage at two points:
first the pin B and then the upper end of the clip
C. (Fig. 7)
To disassemble the armrests, first release the upper
end of the clip C and then the pin B.
5 Maintenance
5.1 General Maintenance Information
This product is maintenance-free, provided that the cleaning
and disinfection instructions are adhered to.
1470052-F
5.2 Cleaning and Disinfection
General Safety Information
CAUTION!
Risk of Contamination
– Take precautions for yourself and use
appropriate protective equipment.
NOTICE!
Wrong fluids or methods can harm or damage
the product.
– All cleaning agents and disinfectants used must
be effective, compatible with one another and
must protect the materials they are used to
clean.
– Never use corrosive fluids (alkalines, acid etc.)
or abrasive cleaning agents. We recommend
an ordinary household cleaning agent such as
dishwashing liquid, if not specified otherwise in
the cleaning instructions.
– Never use a solvent (cellulose thinner, acetone
etc.) that changes the structure of the plastic
or dissolves the attached labels.
– Always make sure that the product is completely
dried before taking it into use again.
For cleaning and disinfection in clinical or long-term
care environments, follow your in-house procedures.
Cleaning Intervals
NOTICE!
Regular cleaning and disinfection enhances
smooth operation, increases the service life and
prevents contamination.
Clean and disinfect the product:
– regularly while in use,
– before and after any service procedure,
– when it has been in contact with any body
fluids,
– before using it for a new user.
Cleaning Instructions
NOTICE!
Maximum cleaning temperature:
– 60 °C by hand
– 85 °C for 3 minutes by automatic washing
systems
1. Clean the product by wiping down all generally accessible
surfaces.
2. Dry the parts with a cloth.
Disinfection Instructions
Method: Follow the application notes for the used
disinfectant and wipe-disinfect all accessible surfaces.
Disinfectant: Ordinary household disinfectant.
Drying: Allow the product to air-dry.
6 After Use
6.1 Disposal
Be environmentally responsible and recycle this product
through your recycling facility at its end of life.
Disassemble the product and its components, so the different
materials can be separated and recycled individually.
The disposal and recycling of used products and packaging
must comply with the laws and regulations for waste handling
5