INSTALLATION INSTRUCTIONS
PLACEmENT OF THE REFRIGERATOR
The room should have a capacity (length x width x height)
of at least 30 m
and must be adequately ventilated as well as
3
follow all relevant national and local regulations. Further the
room should have a window (which can be opened) or a door
to the outside.
It is important that the refrigerator is not subject to radiation
of heat from a stove etc.
For best performance also at high ambient temperatures there
must be a free air circulation over the cooling unit at the rear
of the refrigerator.
The refrigerator is designed for a free-standing installation
and the clearance to the rear wall and to possible side walls,
should be at least 25 mm. The clearance above the refrigera-
tor should be at least 100 mm.
The refrigerator must be adjusted to a vertical position in
both directions. Use the feet on the refrigerator to adjust its
position.
LP GAS CONNECTION
The refrigerator is designed for operation on LP gas, the pres-
sure of which must be 37 mbar for Propane and 28 mbar for
Butane. Check that this is stated on the data plate.
The refrigerator is not designed for operation on town gas or
natural gas.
CAUTION! Check that the gas supplied to the
refrigerator is at the correct pressure . See the
reducing valve on the lp gas container .
The gas installation and servicing should only be carried out
by an authorized, qualified person and must conform to all
relevant national and local regulations.
The gas supply pipe should be connected to the gas inlet of
the gas control valve by means of a suitable threaded cou-
pling.
In making the connection to the refrigerator, a union gas cock
of an approved bottled-gas type must be incorporated in the
supply line in a position, which is readily accessible to the
user. For eventual servicing purposes, the union should be on
the outlet side of the cock and the pipework should be posi-
tioned so as not to prevent the refrigerator from being readily
withdrawn.
ELECTRICAL CONNECTION
The electrical installation must be carried out in a proper and
durable manner; taking into accounts all relevant regulations
and codes of practice.
As the colours of the wires in the mains lead of this appliance
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
•
the wire which is coloured green and yellow must be con-
nected to the terminal in the plug which is marked with
the letter E or by the earth symbol
green and yellow,
•
the wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black,
•
the wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
WARNING! This appliance must be earthed!
NOTE!
It is important that the wires in this main lead are coloured in
accordance with the following code:
•
•
•
Your appliance is already fitted with a 13 amp.(B.S. 1363)
fuse plug incorporating a 3 A fuse. If it does not fit your
socket, the plug should be cut off from the mains lead and an
appropriate plug fitted. Throw away the cut off plug; do not
insert it in a 13 A socket-outlet elsewhere in the house as this
could cause a shock hazard. The fuse cover must be re-fitted
when changing the fuse. Never use the plug without the fuse
cover. The appliance must be protected by a 3 amp. fuse,
ASTA approved to B.S. 1362.
240 V Supplies
Check that the voltage stated on the data plate is the same as
the main voltage in use (240 V). Plug the
240 V refrigerator power cord into an easily accessible
earthed wall socket.
, or coloured green or
Lighting
The refrigerator is provided with a battery power interior
light. The battery box is at the rear of the refrigerator. Four
batteries, type LR20 1,5 volts are to be used.
35
From the side
At least
25 mm
From above
green/yellow:
earth
blue:
neutral
brown:
live
Electrical leads must be routed and secured so
that they cannot come into contact with hot or
sharp parts of the refrigerator .
Wall
25
Wall