EINHELL TC-RH 1600 Manual De Instrucciones Original página 15

L sound pressure level ..................... 93.2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ...................... 104.2 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
The hammer drill is not designed for outdoors
use as specifi ed I Article 3 of Directive 2000/14/
EC_2005/88/EC.
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Hammer drilling in concrete
Vibration emission value a
K uncertainty = 1.5 m/s
Chiseling
Vibration emission value a
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in accord-
ance with a set of standardized criteria and can
be used to compare one power tool with another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may
vary from the level specifi ed during actual use,
depending on the way in which the power tool is
used, especially the type of workpiece it is used
for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Anl_TC_RH_1600_SPK9.indb 15 Anl_TC_RH_1600_SPK9.indb 15
= 16.3 m/s
2
h,HD
2
= 14.965 m/s
2
h,Cheq
2
- 15 -
GB
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Check the drilling point for concealed electrical
cables, gas and water pipes using a cable/pipe
detector.
5.1 Additional handle (Fig. 2 – Item 6)
For safety reasons you must only use the
hammer drill with the additional handle.
The additional handle (6) enables you to achieve
better stability whilst using the hammer drill. The
machine must not be used without the additional
handle (6) for safety reasons.
The additional handle (6) is secured to the
hammer drill by a clamp. Turning the handle anti-
clockwise (looking from the handle) will release
the clamp. Turning the handle clockwise will tigh-
ten the clamp.
First release the additional handle clamp. You can
then swing the additional handle (6) into the most
comfortable working position for you. Now turn
the additional handle in the opposite direction
again until the additional handle is secure.
5.2 Depth stop (Fig. 3 – Item 7)
The depth stop (7) is held in place with the lo-
cking screw (a) on the additional handle (6) by
means of a clamp.
•
Undo the locking screw (a) and fit the depth
28.11.2023 11:04:30 28.11.2023 11:04:30