EINHELL TC-SB 200/1 Manual De Instrucciones Original página 22

Throat: .................................................... 200 mm
Table size: ...................................... 305 x 305 mm
Tilting range of table: ............................. -2° to 45°
Workpiece size: ...................... 400 x 400 x 80 mm
Weight: ......................................................17,5 kg
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L sound pressure level ..................... 84.3 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level .......................... 96 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
5. Before starting the equipment
Make sure the machine stands securely, i.e. bolt it
to a workbench or solid base. There are two holes
for this purpose in the machine foot.
•
The saw table must be mounted correctly.
•
All covers and safety devices have to be pro-
perly fitted before the machine is switched on.
•
It must be possible for the blade to run freely.
Anl_TC_SB_200_1_SPK13.indb 22 Anl_TC_SB_200_1_SPK13.indb 22
GB
•
When working with wood that has been pro-
cessed before, watch out for foreign bodies
such as nails or screws etc.
•
Before you actuate the On/Off switch, make
sure that the saw blade is correctly fitted and
that the machine's moving parts run smoothly.
•
Before you connect the machine to the power
supply, make sure the data on the rating plate
is the same as that for your mains.
6. Assembly
CAUTION!
Pull out the power plug before carrying out any
maintenance, resetting or assembly work on the
bandsaw!
6.1.1 Fitting the rubber feet / tilt guard
(Fig. 5a/ 5b)
Secure the four rubber feet (49) to the bottom
side of the equipment using the screw (51), the
washer (43) and the nut (44).
Push the tilt guard (27) into the foot (5) and se-
cure it to the equipment using the socket head
screw (52), the washer (53) and the nut (54).
6.1.2 Mounting the saw table (Fig. 3 - 4)
•
Remove the web panel (4).
•
Place the saw table (15) onto the machine
housing from the rear. Secure the saw table
using the washers (55), the locking grip (18)
and the locking lever (56).
•
To dismantle, proceed in reverse order.
6.2. Tensioning the blade (Figure 1)
•
CAUTION! Remove the tension from the
blade if the bandsaw is not going to be used
for some time. Be sure to re-tension the blade
before you start the machine.
•
Turn the tightening screw (9) for tensioning
the blade (26) in a clockwise direction.
•
The correct blade tension can be checked
by applying pressure to the side of the blade
with your finger, somewhere in the middle
between the two blade pulleys (7 + 8). You
should only be able to bend the blade (26)
very slightly (approx. 1-2 mm).
•
When the blade is tensioned enough, it will
produce a metallic sound when tapped.
•
Take the tension off the blade when you do
not want to use it for some time; this will help
to prevent overstretching.
- 22 -
12.12.2023 15:30:11 12.12.2023 15:30:11