EINHELL TP-JST 18/135 Li BL Manual De Instrucciones página 14

extraction system (5) as shown in Fig. 5 and
turn the angle adapter for sawdust extraction
(19) into the position of your choice.
•
Fit the vacuum tube of the vacuum cleaner
onto the opening of the adapter for dust
extraction system (5). Check that the
connections are airtight.
5.6 Line guide (Fig. 10-12/Item 6)
Using the line guide (6), you can carry out
exact cuts following cutting lines marked on the
workpiece. Fit the line guide by mounting it on the
top of the soleplate (7) and letting it lock in place
at the bottom, as shown in Fig. 10. Use the mark
(B) for the 0° angle setting (Fig. 11) and the marks
(C) for the 45° angle setting (Fig. 12). See point
5.4 for information about the angle setting.
Important! Carry out trial cuts in a piece of
waste wood.
To remove the line guide (6) simply press it
downwards.
5.7 Splinter guard (Fig. 2/Item 17)
The splinter guard ensures that the material
you want to cut does not splinter or crack
during sawing. Insert it into the soleplate from
underneath as shown in Fig. 2.
Fit the splinter guard into the removable cover
(18) from underneath as shown in Fig. 2. Then
latch it in the removable cover (18) in order to
secure it.
Note! The splinter guard can be used only for 0°
cuts and must be removed for miter cuts up to
45°!
5.8 Removable cover (Fig. 13-14/Item 18)
The adjustable soleplate is equipped with a
removable cover (18). This prevents sensitive
surfaces from becoming scratched.
To fi t the removable cover (18), hook it onto the
front as shown in Fig. 13 and swing it onto the
soleplate at the rear until you hear it latch in place.
To dismantle, proceed in reverse order.
Anl_TP_JST_18_135_Li_BL_SPK7_USA.indb 14 Anl_TP_JST_18_135_Li_BL_SPK7_USA.indb 14
EN
6. Operation
6.1 On/Off switch (Fig. 16/Item 3)
To start the equipment, push the On/Off switch (3)
forward and press it down. To switch off depress
the On/Off switch (3) at the back. The On/Off
switch (3) will jump back into its starting position.
6.2 Adjusting the speed (Fig. 16/Item 2)
You can pre-select the required speed with the
speed selector (2). Turn the speed selector (2)
in PLUS direction to increase the speed, turn
the speed selector (2) in MINUS direction to
reduce the speed. The appropriate stroke speed
depends on the material you want to cut and on
the working conditions.
The general rules for cutting speeds in metal also
apply.
While you can generally use a higher speed with
fi ne saw blades, lower speeds are required for
coarse saw blades.
6.3 Setting the orbital action (Fig. 17/Item 8)
•
The strength of the orbital action of the saw
blade (12) can be adjusted using the selector
switch for orbital action (8).
•
You can adjust the cutting speed, cutting
performance and appearance of the cut to the
workpiece you want to saw.
Set the selector switch for orbital action (8) to one
of the following positions:
Position A = No orbital action.
Material: Rubber, ceramic, aluminum, steel.
Please note: For fi ne clean cuts, thin materials
(e.g. sheet steel) and hard materials.
Position B = Small orbital action.
Material: Plastic, wood, aluminum.
Please note: For hard materials.
Position C = Medium orbital action.
Material: Wood.
Position D = Large orbital action.
Material: Wood.
Please note: For soft materials and sawing along
the grain.
The best combination of speed and orbital action
depends on the material you want to saw. We
recommend you make a trial cut on a waste piece
in order to check the ideal settings.
- 14 -
08.12.2023 11:40:13 08.12.2023 11:40:13