Magnetrol ECLIPSE 706GWR Manual De Operación E Instalación página 34

2.6.5 Menú de Configuración del Modelo 706 — Ajustes de Dispositivo
Home Screen
Main Menu
Device Setup Quick Start
Identity
Basic Config
I/O Config
Display Config
Advanced Config
Factory Config
Level Units: Probe Mount:
Inches NPT
Feet BSP
Millimeters Flange
Centimeters NPT/Flushing
Meters BSP/Flushing
Flange/Flushing
Probe Model: Hygienic
7YD Coax HTHP
7YF Sngl Rod Std Probe Coating:
7YG Sngl Rod Std None (Bare)
7YJ Sngl Rod HTHP PFA Coated
7YL Sngl Rod HP
7YM Sngl Rod HP Probe Length:
7YN Sngl Rod HTHP 12 inches to 100 feet
7YP Coax HP (30 cm to 30 m)
7YS Coax Steam
7YT Coax Std Level Offset:
7Y1 Sngl Flex Std -25 feet to +75 feet
7Y2 Sngl Flex Bulk (-7.6 m to 22.9 m)
7Y3 Sngl Flex HP
7Y5 Twin Flex Bulk Dielectric Range:
7Y6 Sngl Flx HTHP Cage Below 1.7
7Y7 Twin Flex Clad 1.7 to 3.0
3.0 to 10
Above 10
Flow Setup:
34
Measurement Type:
Level Only
Interface and Level
Volume and Level
Flow
Flow Units:
Cubic Ft/Second
Cubic Ft/Minute
Cubic Ft/Hour
Gallons/Minute
Gallons/Hour
Mil Gallons/Day
Liters/Second
Liters/Minute
Liters/Hour
Cubic Meters/Hour
Flow Element:
Palmer-Bowlus Flume
Flume Channel Width:
4 inches
6 inches
8 inches
10 inches
12 inches
15 inches
18 inches
21 inches
24 inches
27 inches
30 inches
Parshall Flume
Flume Channel Width:
1 inch
2 inches
3 inches
6 inches
9 inches
12 inches
18 inches
24 inches
36 inches
48 inches
60 inches
72 inches
96 inches
120 inches
144 inches
57-606 Transmisor de Radar de Onda Guiada ECLIPSE Modelo 706
V-notch Weir Maximum Flow
V-notch Weir Angle: (calculated, read only)
22.5°
30° Low Flow Cutoff:
45° 0 to 9999999 cubic
60° ft/min
90°
120° TOTALIZER SETUP:
Units:
Rect Weir with Ends Cubic Feet
0 to 215.0 feet Gallons
(0 to 65 m) Mil Gallons
Liters
Rect Weir w/o Ends Mil Liters
0 to 215.0 feet Cubic Meters
(0 to 65 m)
NON-RESET
Cipolletti Weir TOTALIZER:
0 to 215.0 feet Multiplier:
(0 to 65 m) 1
10
Generic Equation 100
K 1,000
L 10,000
C 100,000
n
Value (read only)
Custom Table RunTime (read only)
Custom Table Type:
Linear RESETTABLE
Spline TOTALIZER:
Mode:
CUSTOM TABLE Disabled
VALUES: Enabled
Up to 30 Pairs of
Head/Flow Data Multiplier:
1
Reference Distance: 10
11.8 inches to 100 feet 100
(30 cm to 30 m) 1,000
10,000
Maximum Head 100,000
The Maximum Head
value can be revised Value (read only)
depending on the value RunTime (read only)
of the Reference
Distance, or for end user Reset
preference.