Descargar Imprimir esta página

RS Pro RS VP-4 Manual De Instrucciones página 3

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

Non-Contact AC Voltage Detector/English
3- General Specifications
Detection voltage range:
50V AC to 1000V AC, 200V AC to 1000V
Frequency range:
50/60Hz
Batteries:
Two AAA 1.5V batteries
Operating temperature:
32°F to 122°F(0°C to 50°C)
Storage temperature:
14°F to 140°F(-10°C to 60°C)
Humidity:
80% max.
Altitude:
2000 meters
Pollution Degree:
2
Safety Compliance:
CAT IV-1000V
Ingress Protection Rating:
IP67
4-Detector Description
1-Screw on battery cover
3-Flashlight button
5-Tester ON/OFF button
7-Detector tip
5-Operation
1- Turning the Tester On:
Momentarily press the tester
button. The tester will beep and vibrate once and the green
LED will illuminate to indicate that the tester is on and ready
for use.
2- Turning the Tester Off:
Momentarily press the
button. The tester will beep and vibrate twice and the green
LED will turn off.
2
2-Flashlight
4-50V button
6-LED indicators
8-Worklight
ON/OFF
ON/OFF
Non-Contact AC Voltage Detector/English
3-Turning the Beeper and the Vibrating Motor Off:
press and hold the
ON/OFF button until the green LED is
illuminated. The tester will now operate without the beeper or
the vibrating motor. To turn the beeper and the vibrating
motor off when the tester is on, press and hold the
button until the green LED flashes. To turn the beeper and the
vibrating motor back on, press and hold the
until the green LED flashes, the beeper beeps and vibrating
motor vibrates.
4-Verify Operation:
Before using tester, (1)Make sure the green
LED is glowing, (2)Check tester on a known live AC voltage
that is within the defined detection range of the tester.
5-High Voltage Mode(200 to 1000V AC):
an AC voltage. If the tester detects voltage within the defined
detection range, the green LED will turn off, the red LED will
turn on, the beeper will beep rapidly and the vibrating motor
will vibrate when the red LED is illuminated.
6-Low Voltage Mode(50 to 1000V AC):
The green LED will change to yellow to indicate the tester is in
the low voltage mode. While pressing the 50V button, place
the tip of the tester near an AC voltage. When AC voltage is
detected, the yellow LED will turn off, the red LED will flash,
the vibrating motor will vibrate when the red LED is
illuminated and the beeper will beep. The flash rate and
beeping rate will increase as the tester gets closer to the
voltage source. If the tester detects high voltage, it will
automatically change over to the high voltage mode: The red
LED will change to a steady glow and the beeper will beep
rapidly, the vibrating motor will vibrate when the red LED is
illuminated.
NOTE:
The tester cannot determine the actual voltage. The
voltage level where the tester switches from the low to high
voltage mode is effected by insulation type and thickness,
distance from the voltage source, and other factors.
7-Low Battery Indication:
Replace the batteries if the green LED
does not turn on. When the tester is on and the batteries are
too low for reliable operation, the tester will beep and vibrate
three times and the green LED will turn off indicating the tester
is not operational. Replace the batteries to restore operation.
With the tester off,
ON/OFF
ON/OFF button
Place the tip of the tester near
Press and hold the 50V button.
3

Publicidad

loading

Este manual también es adecuado para:

136-5675