höfats SPIN 1500 Instrucciones De Uso página 17

• Only hang the SPIN hanging fire in places
sheltered from the wind to prevent
uncontrolled swinging of the SPIN.
• If the SPIN hanging fire begins to swing, it
must be brought back to its resting position
as quickly as possible. Always use heat-
resistant gloves to avoid burns.
SETTING UP THE SPIN WITH THE RISER
(FIGURE P)
You can use SPIN with a riser. The SPIN can be elevated from the
ground using the riser.
• Screw the riser between the base and the body of the SPIN.
• Insert the Bio-Burner into the body.
• Place the glass cylinder on the body.
• Follow the instructions under "Lighting the fire".
WARNING!
The SPIN must not be used indoors when
set up using the SPIN riser!
Never use more than one riser with the
SPIN!
FILL BIO-BURNER (FIGURE A)
NOTICE
The use of fuels other than those
recommended in the technical data can
lead to unwanted soot formation and less
flame formation or excessively high flames.
In addition, the Bio-Burner can be
destroyed.
Only fill the Bio-Burner with liquid fuels
from höfats. This is the only way to ensure
that it operates properly.
• Before filling with liquid fuel, check the Bio-Burner for dirt or
damage.
• Insert the Bio-Burner into the body of the SPIN (Figure A1).
• Fill the Bio-Burner with the liquid fuel suitable for your Bio-Burner
up to the "max" mark (Figure A2).
LIGHTING THE FIRE (FIGURE B)
Optional: Use Bio-Burner with Eco-Ring
(Figure B1)
• If you put the Eco-Ring on the Bio-Burner after filling, the flame
is reduced a little and you save liquid fuel! This also means your
SPIN will burn for longer.
– Risk of burns from hot
CAUTION!
surfaces! Only touch the Eco-Ring when
it has cooled down and not directly after a
burning process.
• Light the Bio-Burner at the mesh with a stick lighter
(Figure B2).
CAUTION!
Risk of burns from using unsuitable
fire-starters!
Improper use of fire-starters poses a risk
of burns.
Use a stick lighter to light.
CAUTION!
Risk of burns!
The flame may be difficult to see after
lighting. You may burn yourself or come
into contact with burning liquid fuel while
attempting to check for a flame.
• After lighting, always put the glass cylinder
on the SPIN first.
• Do not look into the glass cylinder from above!
• Wear grill gloves when handling the SPIN
after lighting it.
WARNING!
Risk of fire from improper ignition of the
Bio-Burner!
If you light the Bio-Burner without first
inserting it into the SPIN, you can burn
yourself on the hot can when inserting it
into the wing body. In addition, burning
liquid fuel may leak and cause a fire.
• Only light the Bio-Burner after you have
inserted it into the body.
EXTINGUISHING THE FIRE (FIGURE D)
Extinguishing the Bio-Burner
• To extinguish the Bio-Burner, grasp the extinguishing cover by
the wire (Figure D1).
• Then lower the cover into the glass cylinder until it rests on the
Bio-Burner (Figure D2).
• Wait for the flame to go out and the SPIN to cool before lighting
or moving the SPIN again.
CAUTION!
Never use extinguishing covers from other
höfats products to extinguish the Bio-Burner!
Do not use any other covers than the
extinguishing cover to extinguish the SPIN!
Do not leave the SPIN unattended after
extinguishing without checking to ensure it
the flame is really out.
After extinguishing
After you have extinguished the Bio-Burner and all parts have
cooled down, you can do the following:
• Refill the Bio-Burner with fuel and ignite.
• Insert a new Bio-Burner into the SPIN, fill it up and ignite.
• Empty and discard any remaining fuel in the Bio-Burner.
Observe the local/national regulations for the disposal of liquid
fuel.
EN