Publicidad
Idiomas disponibles
Idiomas disponibles
GB
TRACK
the openings in the wooden base and pull through the front of the seat fabric. To reinstall, repeat
the process in reverse and ensure that each harness belt is secured.
H
ATTACHING FOOTWARMER
Align the zip located on the edge of the footwarmer to the zip located on the seat unit/ pram
body and fasten.
Fold the flap around the bumper bar and fasten into place with the press studs.
I
USING THE PRIVACY PANEL
1. To use the privacy panel, detach the apron fastenings from around the bumper bar.
2. Reattach the fastenings to the inside of the hood.
J
USING THE BRAKES
1. To engage the brake, apply a light downward pressure to the brake lever. Ensure that the bra-
kes have been applied correctly and that the stroller will not move.
2. To release the breaks, gently lift up the brake lever.
K
USING THE FRONT WHEELS
1. Pull the lever located at the rear of the front wheel inwards towards the pram to engage the
front wheel lock.
2. To release the lock, pull the lever outwards. Note that each wheel will require the lever to be
pulled in a different direction - inwards & outwards, and not left or right.
L
OPERATING THE SEAT RECLINE
1. To recline the seat, lift the handle located at the top of the seat unit.
2. The seat has 3 positions - Fully reclined, mid recline and upright.
3. Please note that the fully upright position should only be used for a child over 6 months old.
NOTE: When using from birth please make sure the pushchair is in the pram mode.
M
FOLDING DOWN THE STROLLER
1. Ensure to remove the pram body/seat unit before folding. Locate the fold levers (on each side
of the chassis) and the fold lock button (on the right hand side of the chassis). To fold, press
down the fold lock button while pulling the fold levers towards the handle bar.
2. Once the TRACK stroller begins to fold, (A) release the folding button and allow to fully fold.
3. Secure the TRACK stroller in the folded position by ensuring the latch has fastened.
N
CONNECTING CAR SEAT TO STROLLER OR PRAM
1. Prepare your pram or stroller for car seat fitment. Refer to your stroller manual for guidance in
attaching the car seat adaptors correctly.
2. Lift and lower the car seat onto the stroller or pram adaptors so they slide into the slots found
underneath the left and right handle hubs of the car seat.
NOTE: The car seat must be parent facing.
3. When correctly aligned with the adaptors, apply even pressure on the left and right sides of
the car seat until you hear a 'click' to confirm it is locked in position.
4. To release the car seat from the pram or stroller, press and hold each of the adaptor release
buttons, whilst simultaneously lifting the car seat up.
The adaptor release buttons are located above the adaptors, on the inside of the carry handle
on the car seat as shown.
32
GB
TRACK
O
CONVERTING PRAM BODY TO SEAT UNIT
1. To convert pram body to seat unit, connect the two clips located at the bottom of the pram
body/seat unit.
2. Tighten the toggle located on the top of the pram body/seat unit by holding the strap
taught and pushing the toggle upwards. Ensure that all fabrics and buckles are secure befo-
re use.
3. To convert seat unit back into pram body, disconnect the two clips located at the bottom of
the seat unit and loosen the toggle at the top by squeezing the two side buttons and pulling
down. Push the fabric downwards from the inside to ensure the pram body lies flat.
INFORMATION ABOUT THE GUARANTEE
- This item is guaranteed against manufacturing defects as stipulated in the legal Directives
and/or regulations in force on guarantees for consumer goods applicable to the European
Union and those of the country in which it is marketed.
- It is essential to present the purchase invoice or receipt in order to process the guarantee
through the seller of the item or, failing that, through the manufacturer.
- The guarantee excludes anomalies or faults caused by misuse, non-compliance with the
safety regulations and instructions for use and maintenance provided, or due to wear and
tear caused by normal use and regular handling of the item.
- The label containing the serial number of your model must not be torn off under any cir-
cumstances as it contains information relevant to the guarantee.
MAINTENANCE
Keep the metal parts clean and dry to prevent rusting.
Regularly grease the mobile parts and mechanisms with a silicone-based spray. Do not use oil or
grease. Only use mild detergent and warm water to clean the plastic parts.
Do not expose the upholstery to sunlight for prolonged periods of time. The upholstery can be
taken off and washed.
33
Publicidad
