Descargar Imprimir esta página

Hama 00221065 Instrucciones De Uso página 5

Ocultar thumbs Ver también para 00221065:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
4. First steps - Inserting the batteries
Note
• Use 2 type AAA batteries.
• Remove the battery compartment cover on the underside of the
remote control (Pic. A).
• Ensure the correct polarity (+/-) of the batteries and the battery
compartment.
• Insert the batteries (Pic. B).
• Reattach the battery compartment cover on the remote control
(Pic. C).
Note - code memory
This remote control saves the settings even during a battery change.
Note: Energy saving function
The remote control switches itself off automatically if a button is
pressed for longer than 15 seconds. This prolongs the life of the
batteries if the remote control is stuck in a place where the buttons
are pressed permanently, e.g. between sofa cushions.
Note:
Low battery display
• This remote control indicates when the batteries are getting low.
• If the status LED ashes 2 times after a button is pressed, the
batteries are weak and should be replaced promptly.
5. Setup
With the factory settings supplied, the remote control can control
approx. 90% of all GRUNDIG devices. There is no need to make any
settings. If the remote control does not work, select one of the setting
options mentioned in 5.1 and 5.2 below.
5.1 Code input
CODE list:
001, 002, 003, 004, 005, 006, 007, 008, 009, 010, 011, 012, 013,
014, 015, 016, 017, 018, 019, 020, 021, 022, 023, 024, 025, 026,
027, 028, 029, 030, 031, 032, 033, 034, 035, 036, 037, 038, 039,
040, 041, 042, 043, 044, 045, 046, 047, 048, 049, 050, 051, 052,
053, 054, 055, 056, 057, 058, 059, 060, 061, 062, 063, 064,
065, 066
1. Press and hold the [MUTE] and [POWER] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.
2. Enter a 3-digit code from the code list using the number keys. The
status LED confirms each number entered with a short flash. When
all three digits have been entered, the status LED goes out. If you
have entered an invalid device code, the status LED flashes 3 times
and then lights up permanently again for a new code entry.
3. Test the functions of the remote control. If the function does not
work properly, try other device codes: [002], [003], [004], etc.
Note
• If no button is pressed within approx. 15 seconds, the set-up
programme is automatically terminated.
• If an invalid code is entered, the status LED ashes 3 times and
then lights up again permanently.
• To exit the set-up programme, press the [MUTE] button.
5.2 Code search
1. Press and hold the [MUTE] and [POWER] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.
2. Press the [P+ or P-] button to start the code search. With each
button press, the remote control sends a new code to your TV. If
your TV switches to a different programme, also test the found
device code using the [POWER], [VOL+], [VOL-], [MENU] buttons
and the number keys 0-9. If the functions work, press the [MUTE]
button to save the device code and end the search.
3. Test the found device code with the [POWER], [VOL+], [MENU] and
[0-9] buttons. If the functions work, press the [MUTE] button to save
the device code and exit the search.
4. If the functions do not work,
repeat the search by pressing the [P+] or [P-] button.
VI

Publicidad

loading