Descargar Imprimir esta página

Hama 00221065 Instrucciones De Uso página 6

Ocultar thumbs Ver también para 00221065:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 16
Note
In programming mode, only the [POWER], [VOL+], [MENU] and [0-9]
buttons work.
5.3 Code query
You can display the code currently used by the remote control:
1. Press and hold the [MUTE] and [POWER] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.
2. Enter the numerical sequence [9] [9] [0] with the numerical keys
(the LED flashes with each entry). The status LED flashes twice and
goes out.
3. Press the button [1] for the first digit of the code. The status LED
starts to flash.
Count the number of individual flashes of the status LED - this
number corresponds to the first digit of the current device code.
Proceed accordingly for the 2nd and 3rd digits of the code:
2nd digit -> enter 2 -> count flashing signals
3rd digit -> enter 3 -> count flashing signals
If one digit of the device code is a 0, the status LED does not flash.
After the third digit has been displayed, the status LED goes out.
5.4 Overview of compatible remote controls
Due to the large number of different remote controls, we can only
provide a limited number in the code list. If the button diagram and
housing shape of your original remote control match one of the models
shown, it is compatible (www.hama.com
6. Learning function
This remote control is equipped with a learning function. This allows
you to transfer functions from your original remote control to this
remote control.
6.1 Before you start the learning function
• Make sure that all batteries used in both remote controls are in
perfect condition. Change them if necessary.
• Place your original remote control and the remote control next to
each other so that the infrared diodes of the remote controls are
directly opposite each other.
• If necessary, correct the height of both remote controls to achieve
optimal alignment.
• The distance between the two remote controls should be approx.
3 cm.
ROC1117GRU
HAMA
ORIGINAL
ca. 3 cm
VII
00221065
Downloads).
Note
• Do not move the remote controls during the learning process.
• Make sure that the room lighting is not uorescent tubes or
energy-saving lamps, as these could cause interference and thus
hinder the learning process.
• The distance between the two remote controls and the nearest
light source should be at least 1 metre.
• The learning process is terminated without saving if no button is
pressed or no signal is received for 15 sec. while learning mode
is activated.
• In learning mode, each button can only be assigned one function.
A new function overwrites the function previously taught on this
button.
6.2 Activating the learning mode
1. Press and hold the [MUTE] and [VOL+] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.
2. Enter the code [9] [8] [0], the status LED flashes 2 times and then
lights up permanently.
3. The remote control is now in learning mode.
6.3 Transferring the button function
1. Press the button on the original remote control whose function you
want to transfer. To confirm that the command has been received,
the status LED of the replacement remote control flashes.
2. Now press the button on the replacement remote control to which
the function is to be transferred.
3. The function LED of the replacement remote control flashes 3 times
for confirmation and then lights up permanently again. The new
function is now saved.
4. To transfer the functions of additional buttons, repeat these steps.
5. Press the [OK] button to save all taught-in functions and exit the
learning mode.
Note
When changing the batteries of the remote control, the functions of
the taught-in buttons are retained.
6.4 Deleting taught functions
6.4.1 Deleting a taught function
1. Press and hold the [MUTE] and [VOL+] buttons simultaneously for
approx. 3 sec. until the status LED lights up continuously.

Publicidad

loading