DeWalt DW082 Manual De Instrucciones página 2

The two beams are plumb as long as the calibration has been checked (see Field Calibration
Check section below) and the laser beam is not flashing (see Out of Tilt Range Indicator
section below).
The tool can be used to transfer a point up or down by using one beam to locate the Laser
Plumb Bob, and then transferring the point using the other beam.
NOTE: The Laser Plumb Bob has magnets which can be used to help position the tool against
steel track fastened to the floor. The magnets are for alignment purposes only and SHOULD
NOT BE USED TO SUPPORT THE WEIGHT OF THE TOOL. Always make sure the tool is posi-
tioned securely and on a smooth surface
OUT OF TILT RANGE INDICATOR
The DW082 Laser Plumb Bob is designed to self-plumb. If the laser has been tilted so much
that internal mechanism cannot plumb itself (> 4° tilt), it will flash the laser beam (Fig. 5). The
flashing dot indicates the tilt range has been exceeded and IS NOT PLUMB AND SHOULD NOT
BE USED FOR DETERMINING OR MARKING PLUMB. Try repositioning the laser on a more
level surface.
USING THE LASER WITH ACCESSORIES
The laser is equipped with a 1/4" x 20 female thread on the bottom of the unit. This thread is to
accommodate current or future D WALT accessories. Only use D
E
for use with this product. Follow the directions included with the accessory.
CAUTION: The use of any other accessory not recommended for use with this tool could be
hazardous.
If you need any assistance in locating any accessory, please contact D
Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-D
See our catalog on the World Wide Web at www.dewalt.com.
PLUMBING THE LASER PLUMB BOB
As long as the tool is properly calibrated, this tool is self-plumbing. It is calibrated at the factory
to find plumb as long as it is positioned on a flat surface within 4° of level. No manual adjust-
ments must be made.
MAINTENANCE
To maintain the accuracy of your work, have the laser checked often to make sure it is proper-
ly calibrated. See the Field Calibration Check section of this manual.
Calibration checks and other maintenance repairs may be performed by D
ters.
When not in use, store the laser in the kit box provided. Do not store your laser at temperatures
below 0°F or above 185°F.
CAUTION: Do not store your laser in the kit box if the laser is wet. The laser may be dried
first with a soft dry cloth.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth and mild detergent. Although these
parts are solvent resistant, NEVER use solvents. Use a soft dry cloth to remove moisture from
the tool before storage.
Field Calibration Check
This section provides instructions by which you can perform a simple field calibration check of
your D WALT Laser Plumb Bob.
E
Checking the plumb calibration of the laser can be most accurately done when there is a sub-
stantial amount of vertical height available, ideally 50', with one person on the floor positioning
the laser and another person near a ceiling about 50' higher to mark the dot on the ceiling
(Fig. 6). It is important to conduct a calibration check using a vertical distance no shorter than
the vertical distance of the applications for which the tool will be used.
1. Start by marking a point on the floor.
2. Place the laser so that the down beam is centered on the point marked on the floor.
3. Allow time for the laser to settle to plumb and mark the center of the dot created by the up
beam.
4. Turn the laser 180° as shown (Fig. 7), making sure that the down beam is still centered on
the point previously marked on the floor.
5. Allow time for the laser to settle to plumb and mark the center of the dot created by the up
beam.
NOTE: The distance between the two marks on the ceiling is TWICE the actual error.
The two marks on the 50' high ceiling should be no more than 1/4" apart. If the vertical distance
being used is much less than 50', than the dots should be closer.
Troubleshooting
THE LASER DOES NOT TURN ON
• Make sure batteries are installed according to the label in the battery compartment.
• Make sure the batteries are in proper working condition. If in doubt, try installing new
batteries.
• Make sure that the battery contacts are clean and free of rust or corrosion. Be sure to keep
the Laser Plumb Bob dry and use only new, high-quality, name brand batteries to reduce the
chance of battery leakage.
• While the laser may be stored in temperatures up to 185°F (85°C), the laser has a built-in
protection circuit that will not allow it to operate at temperatures in excess of 104°F (40°C).
If the laser has been stored in extremely hot temperatures, allow it to cool. The Laser Plumb
Bob will not be damaged by pressing the ON/OFF button before cooling to its proper oper-
ating temperature.
THE LASER BEAMS FLASH
The DW082 Laser Plumb Bob has been designed to self-plumb up to 4° in all directions when
positioned as shown in Figure 4. If the laser is tilted so much that internal mechanism cannot
plumb itself, it will flash the laser (Fig. 5) – the tilt range has been exceeded. THE FLASHING
DOT CREATED BY THE LASER IS NOT PLUMB AND SHOULD NOT BE USED FOR DETER-
MINING OR MARKING PLUMB. Try repositioning the laser on a more level surface.
THE LASER DOTS WILL NOT STOP MOVING
The DW082 is a precision instrument. Therefore, if it is not positioned on a stable (and motion-
less) surface, the tool will continue to try to find plumb. If the dot will not stop moving, try plac-
ing the tool on a more stable surface. Also, try to make sure that the surface is relatively flat, so
that the laser is stable.
Service & Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be
performed by authorized service centers. Service or maintenance performed by unqualified per-
sonnel may result in a risk of injury. To locate your nearest D
4-D WALT (1-800-433-9258) or go to http://www.dewalt.com on the Internet.
E
Light Source Semiconductor laser diode
Laser Wavelength 630 – 680 nm Visible
Laser Power <1mw (each beam) CLASS II LASER PRODUCT
Working Range ±100' (30m)
Accuracy* (Up) ±1/8" @ 50' (±3mm @ 15m)
Accuracy* (Down) ± 1/4" @ 50' (±6mm @ 15m)
Indicators Flashing Indicator: battery low
Flashing Laser: tilt range exceeded
Power Source 4 AA Size Batteries (6.0V DC)
Operating Temperature 32°F to 104°F (0°C to 40°C)
Storage Temperature 0°F to 185°F (-40°C to 85°C)
Environmental Water Resistant
*Accuracy spec assumes laser is positioned on a surface within 4° of level
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for three
E
years from the date of purchase. This warranty does not cover part failure due to normal wear
or tool abuse. For further detail of warranty coverage and warranty repair information, visit
www.dewalt.com or call 1-800-4-D WALT (1-800-433-9258). This warranty does not apply to
E
WALT accessories specified
E
WALT Industrial Tool
E
WALT (1-800-433-9258).
E
E
WALT service center call 1-800-
E
SPECIFICATIONS
accessories or damage caused where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have other rights which vary in certain
states or provinces.
In addition to the warranty, D
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any time
E
during the first year after purchase.
If you are not completely satisfied with the performance of your D
Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt
for a full refund – no questions asked.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are miss-
ing, call 1-800-4-D
FIG. 1
WALT service cen-
FIG. 3
FIG. 6
POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL OU DE TOUT AUTRE
OUTIL D WALT, COMPOSER LE NUMÉRO SANS FRAIS : 1 800 4-D
E
Directives de sécurité relatives aux lasers
AVERTISSEMENT! Il faut lire et comprendre toutes les directives. Le non-
respect des directives présentées ci-dessous pourrait causer un choc électrique,
un incendie et/ou des blessures graves.
AVERTISSEMENT : Exposition à des radiations laser. Ne pas démonter ou modifier le
niveau laser. Il ne comporte à l'intérieur aucune pièce réparable par l'utilisateur. De
sérieuses lésions oculaires pourraient en résulter.
AVERTISSEMENT : Radiation dangereuse. Toute utilisation des commandes ou exécution
des procédures ou tout réglage non conforme aux spécifications inclues dans les présentes pose
des risques d'exposition à des radiations laser dangereuses.
• Ne pas faire fonctionner le laser dans des atmosphères explosives, comme en
présence de liquides, de gaz et de poussières inflammables. Les outils électriques
produisent des étincelles qui peuvent enflammer la poussière ou les vapeurs.
• N'utiliser le laser qu'avec le bloc-piles spécialement conçu pour celui-ci. L'utilisation
d'autres blocs-piles peut causer un risque d'incendie.
• Ranger le laser hors de la portée des enfants et des autres personnes non qualifiées.
Les lasers sont dangereux entre les mains d'utilisateurs non qualifiés.
• N'utiliser que les accessoires recommandés par le fabricant du modèle. Des
accessoires qui conviennent à un laser particulier peuvent être dangereux lorsqu'ils sont
installés sur un autre laser.
• Seules des personnes qualifiées peuvent réparer les outils. Une réparation ou un
entretien effectué par une personne non qualifiée risque d'entraîner des blessures.
Pour localiser le centre de service D
(1 800 433-9258) ou visiter le site Web http://www.dewalt.com.
• Ne pas utiliser d'outils optiques tels qu'un télescope ou un tachéomètre pour observer
le rayon laser. Une grave blessure à l'œil pourrait en résulter.
• Ne pas placer le laser dans une position qui pourrait permettre à quiconque,
intentionnellement ou non, de regarder directement le rayon laser. Une grave blessure
à l'œil pourrait en résulter.
• Désactiver le laser lorsqu'il n'est pas utilisé. Le risque de regarder directement le rayon
laser augmente si l'outil demeure activé.
• Ne pas démonter l'outil laser. Aucune pièce interne ne peut être réparée par l'utilisateur.
• Ne pas modifier le laser de quelque façon que ce soit. Une modification de l'outil peut
entraîner une exposition dangereuse au rayonnement laser.
• Ne pas faire fonctionner le laser à proximité des enfants ou permettre à ces derniers
de le faire fonctionner. Une grave blessure à l'œil pourrait en résulter.
• Ne pas retirer ou défigurer les étiquettes d'avertissement. Le retrait des étiquettes
augmente le risque d'exposition à la radiation.
• Positionner le laser de façon sécuritaire sur une surface de niveau. La chute de l'outil
pourrait entraîner des dommages au laser ou de graves blessures.
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
90 DAY MONEY BACK GUARANTEE
WALT for a free replacement.
E
FIG. 2
FIG. 4
B
C
D
E
50'
FIG. 7
CONSERVER CES CONSIGNES
WALT le plus près, composer le 1 800 4-DEWALT
E
WALT Power Tool, Laser, or
E
A
FIG. 5
FLASHING
CLIGNOTEMENT / PARPADEO
4°
>
WALT (1 800 433-9258)
E