EINHELL TE-BJ 900 Manual De Instrucciones Original página 17

Danger: Never press the spindle lock (9) while
the motor is running. Check that the cutter is stati-
onary and securely seated before starting work.
Note: Do not use blunt or damaged disk cutters.
6. Operation
6.1 On/Off switch (Fig. 3; item 1)
To start the unit, slide the On/Off switch (1) for-
ward and press it down. To switch off the biscuit
jointer, depress the On/Off switch (1) at the back.
The On/Off switch (1) will jump back into its star-
ting position.
6.2 Marking a workpiece (Fig. 10)
Before you start working with the biscuit jointer,
the workpiece must be marked as follows:
•
Place the two parts side by side; the workpie-
ces must be securely clamped.
•
Draw a line with a pencil at right angles to the
joint.
•
Multiple joints will be required on longer pie-
ces of wood.
•
The distance between two lines should be at
least 10 cm.
Note:
On thicker workpieces you can create additional
stability by cutting two slots one above the other;
on thinner workpieces a single joint will be suf-
fi cient.
6.3 Positioning the biscuit jointer and cutting
slots (Fig. 11)
Cutting slots with an angle of 0° at a particu-
lar height
•
Adjust the angle stop (11) to 0° and then in-
sert the height-adjustable stop (14).
•
Adjust the required height with the aid of the
height-adjustable stop (14) (see 5.5).
•
Position the machine close to the workpiece.
•
There are markings (a) on the machine; the-
se must line up with the line marked on the
workpiece.
•
Then switch on the machine and push the
handle (12) forward. The workpiece must be
securely clamped when doing this.
Anl_TE_BJ_900_SPK13.indb 17 Anl_TE_BJ_900_SPK13.indb 17
GB
Cutting slots with an angle between 0° and
90°
•
Adjust the required cutting depth and check
it (see 5.2).
•
Adjust the required cutting angle using the
angle stop (11) (see 5.3).
•
Position the machine close to the workpiece.
•
There are markings (a) on the machine; the-
se must line up with the line marked on the
workpiece.
•
Then switch on the machine and push the
handle (12) forward. The workpiece must be
securely clamped when doing this.
CAUTION! The height-adjustable stop (14) must
only be used with a cutting angle of 0°.
6.4 Connecting the workpieces (Figs. 12-13)
•
Once you have cut a slot on both workpieces
they can be connected.
•
Apply glue in both slots.
•
Insert the biscuit (a) into one of the slots (Fig.
12).
•
Slide both workpieces together (Fig. 13).
•
Clamp the workpieces and wait until the glue
has set.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
- 17 -
10.08.2023 09:16:12 10.08.2023 09:16:12