Peg-Perego culla belvedere Instrucciones De Uso página 21

3 FOOT MUFF: Fit the foot muff and button it to the side.
4 The magnets can be used to fasten the foot muff to the
hood, granting the child even more protection.
Just lift the foot muff flap as shown.
5 The hood comes with a visor which can be opened for
greater protection against the sun.
The visor is stored inside the hood and is opened simply by
pulling it outwards.
6 GRAND PANORAMA VIEW: The pram body has two
windows, which can be used together or separately for
greater ventilation and to check on baby while asleep:
Upper window .
The hood panorama window is opened by pulling the
protective fabric upwards.
7 Lower window
The zips below the hood open another window level with
baby's head (Fig.a).
When both are opened, the two windows ensure greater
ventilation and visibility (Fig.b).
The pram body's panorama windows can be opened and
closed via zips. Culla Belvedere with both zips closed (Fig.c).
IMPORTANT: When the pram is moving, we recommend
closing the panorama window level with baby's head.
8 COMFORT SYSTEM
Culla Belvedere features a Comfort System that can be
regulated using the knob on the external base (foot end) of
the pram body.
Pull the knob outwards (Fig.a)
If you wish to raise the backrest and footrest, turn the knob
counterclockwise ;
to lower the backrest and footrest, turn the knob clockwise
.
When finished, return the knob to its horizontal position.
9 CARRY HANDLE: the handle bar is fitted with a carry
handle.
_ Before lifting the bassinet, ensure the built-in hood is
correctly fastened.
_ Before lifting the bassinet, make sure the hood is in the
correct position for transport.
_ Before unfastening and lifting the bassinet from the frame,
adjust the backrest to its lowest position.
10 To fasten the bassinet, position it on the frame and press
down with both hands until it clicks into place.
Always enable the brake on the frame before fastening and
unfastening the bassinet.
IMPORTANT: Ensure the bassinet is properly fastened.
11 To unfasten the bassinet, lift the two side levers on the
joints (Fig.1) and release it from the frame (Fig.2).
12 Inside zipped pocket: handy compartment to store and keep
useful items to hand.
WARNING: the storage pockets inside the pram body
must always remain closed.
REMOVING THE HOOD:
13 It is possible to remove the hood.
Unbutton all the buttons on the lower profile, as shown in
the figure.
14 Press the button (Arrow 1) and raise the hood attachment
(Arrow 2).
Pull out the attachment (Arrow 3) and remove the hood
(Arrow 4).
15 Remove the two rigid supports.
16 To remove the lining of the pram body:
Remove the mattress (Fig.a).
Inside the pram body, in the lower section (Fig.b), release the
rigid textile strip by pulling it along the entire perimeter, as
shown in the figure;
17 In the upper section (Fig.c), release the rigid textile strip by
pulling it first centrally (arrow 1) and then laterally (arrow 2),
then lift the fabric (arrow 3).
18 Open the zips on the upper edge of the pram body, first at
the head end (Fig.d) and then at the foot end (Fig.e).
19 Remove the net from the headrest (Fig.f ) and remove the
pram body's entire inner lining by pulling upwards (Fig.g).
REPOSITIONING THE LINING:
20 Reposition the lining in the pram body (Fig.a).
Close the zips on the upper edge of the pram body, first at
the head end (Fig.b) and then at the foot end (Fig.c).
21 Inside the pram body, in the lower section, first position the
fabric well under the headrest (Fig.d), then reposition the
rigid textile strip along the entire perimeter, as shown in the
figure (Fig.e);
22 In the upper section (Fig.f ), reposition the rigid textile strip
21