Descargar Imprimir esta página

Ninja FOODI POWER MIXER SYSTEM CI100 Serie Guia Del Propietario página 5

Publicidad

Idiomas disponibles

Idiomas disponibles

USING THE 3-CUP CHOPPER
(not included with all models)
IMPORTANT:
• Review all warnings before proceeding.
• The processing lid is NOT dishwasher safe.
NOTE:
• DO NOT add ingredients before completing installation of the blade assembly.
• DO NOT operate the chopper continuously for more than 15 seconds at a time.
• DO NOT fill past the MAX FILL line.
1
Place the chopper bowl on a clean, dry, level surface,
such as a countertop or table.
2
Exercising care, grasp the blade assembly by the top
of the shaft and place it onto the drive gear inside
the chopper bowl.
3
Add ingredients to the chopper bowl, then place the
processing lid on top of the bowl, aligning the lid
with the notches in the bowl. Ensure the lid is fully
installed; there will be no click.
6 When finished, unplug the unit. Remove the power
base from the chopper attachment by pressing and
holding the release buttons on either side of the
power base and lifting up.
7
Remove the lid by lifting it up. Always remove the
blade assembly before emptying ingredients from the
bowl by carefully grasping it by the top of the shaft
and lifting it out of the bowl.
8
DO NOT store blended contents with the blade
assembly and processing lid attached. Only use the
storage lid.
9 Refer to the Care & Maintenance section for cleaning
and storage instructions.
ninjakitchen.com
4 Attach power base by aligning the arrow on the
power base with the arrow on the processing lid,
then push the power base onto the lid to lock it
in place. Plug the unit in.
5
Press and hold the
button to process. Use
short presses for short pulses and long presses
for long pulses. The TURBO button is disabled
when using the chopper attachment.
CARE & MAINTENANCE
WARNING:
Handle the chopper blade with care when washing, as the blades are sharp.
Contact with the blade's edges can result in laceration.
CLEANING
• Hand-Washing
Wash immersion blender attachment, beaters, dough hooks, whisk, chopper bowl, storage lid, and
blade assembly in warm, soapy water. Use a dishwashing utensil with a handle to avoid direct contact
with the blades on the immersion blender attachment and the chopper blades. Exercise care when
handling blade assemblies, as blades are sharp. Thoroughly rinse and air-dry all parts.
• Dishwasher
All attachments, with the exception of the power base, hand mixer attachment and the chopper
processing lid, are dishwasher safe.
• Motor Base, Hand Mixer Attachment, Chopper Processing Lid
Unplug the power base before cleaning. Wipe the power base, hand mixing attachment, and chopper
processing lid with a clean, damp cloth. Do not submerge these parts in water.
STORING
For cord storage, wrap the cord with the plastic clip.
RESETTING THE MOTOR
This unit features a unique safety system that prevents damage to the motor and drive system should
you inadvertently overload it. If the unit is overloaded, the motor will be temporarily disabled. Should this
occur, follow the reset procedure below.
1
Unplug the unit from the electrical outlet.
2
Allow the unit to cool for approximately 15 minutes.
3
Remove the attachment. Make sure no ingredients are jamming the accessory.
IMPORTANT: Ensure that maximum capacities are not exceeded. This is the most typical cause of
appliance overload.
If your unit needs servicing, please call Customer Service at 1-877-646-5288. So we may better assist you,
please register your product online at registeryourninja.com and have the product on hand when you call.
ORDERING REPLACEMENT PARTS & ACCESSORIES
To order additional parts and attachments, visit ninjaaccessories.com.
4-Cup Blending Pitcher:
Large pitcher perfectly designed for the immersion blender
attachment to blend your favorite recipes.
ninjakitchen.com

Publicidad

loading