Publicidad
Idiomas disponibles
Idiomas disponibles
Turning On/Off the TV
Connect power
IMPORTANT: The TV set is designed to operate on
220-240V AC, 50 Hz socket.
After unpacking, allow the TV set to reach the ambient
room temperature before you connect the set to the
mains.
Plug one end (the two-hole plug) of the supplied
detachable power cord into the power cord inlet on
the rear side of the TV as shown above. Then plug
the other end of the power cord into the mains socket
outlet. The TV will switch on automatically.
Note:
on the model.
To switch on the TV from standby
If the TV is in standby mode the standby LED lights
up. To switch on the TV from standby mode either:
Press the Standby button on the remote control.
Press the control button on the TV.
The TV will then switch on.
To switch the TV into standby
The TV cannot be switched into standby mode via
control button. Press and hold the Standby button on
the remote control. Power o dialogue will appear on
the screen. Highlight OK and press the OK button. The
TV will switch into standby mode.
To switch o the TV
To power down the TV completely, unplug the power
cord from the mains socket.
Quick Standby Mode
In order to switch the TV into quick standby mode
either;
Press the Standby button on the remote.
Press again to go back to operating mode.
Press the control button on the TV.
Press the control button again to go back to operating
mode.
Your TV continues to operate in the quick standby
mode state, as it regularly checks for updates. This is
not a malfunction, it meets the requirements for energy
consumption. In order to minimise energy consumption
switch your TV into standby mode as explained above.
TV Control & Operation
The control button allows you to control the Quick
Standby-On function of the TV.
Note:
on the model.
To turn the TV o (Quick Standby): Press the control
button to turn the TV into quick standby mode.
To turn the TV o
(Standby): The TV cannot be
switched into standby mode via control button.
To turn on the TV: Press the control button, the TV
will turn on.
Note: Live TV settings menu OSD in Live TV mode cannot be
displayed via the control button.
Operation with the Remote Control
Press the Menu button on your remote control to
display Live TV settings menu when in Live TV mode.
Press Home button to display or return to the Home
Screen of the Android TV. Use the directional buttons
to move the focus, proceed, adjust some settings and
press OK to make selections in order to make changes,
set your preferences, enter a sub-menu, launch an
application, etc. Press Back/Return to return to the
previous menu screen.
Input Selection
Once you have connected external systems to your
TV, you can switch to di erent input sources. Press the
Source button on your remote control consecutively
or use the directional buttons and then press the OK
button to switch to di erent sources when in Live TV
mode. Or enter the Inputs menu on the Home Screen,
select the desired source from the list and press OK.
Changing Channels and Volume
You can adjust the volume by using the Volume
+/- buttons and change the channel in Live TV mode
by using the Programme +/- buttons on the remote.
English - 7 -
Remote Control
Inserting the Batteries into the Remote
The remote may have a screw that secures the battery
compartment cover onto the remote control (or this may
be in a separate bag). Remove the screw, if the cover
is screwed on previously. Then remove the battery
compartment cover to reveal the battery compartment.
Insert two 1.5V - size AAA batteries. Make sure the (+)
and (-) signs match (observing correct polarity). Do not
mix old and new batteries. Replace only with same or
equivalent type. Place the cover back on. Secure the
cover again with the screw, if any.
To pair remote with the TV
When the TV is turned on for the rst time, a search
for accessories will be performed after the initial setup
starts. You will need to pair your remote control with
your TV at this point.
Press and hold the Source button on the remote until
the LED on the remote starts to blink, then release
the Source button. That means the remote is in
pairing mode.
Now you will wait for the TV to nd your remote. Select
the name of your remote and press OK when it appears
on the TV screen.
When the pairing process is successful, the LED on
the remote will go o . If the pairing process fails the
remote will enter sleep mode after 30 seconds.
In order to pair your remote later on, you can go to
Settings menu, highlight Remotes & Accessories
option and press OK to start a search for accessories.
1.
Standby: Quick Standby / Standby / On
2.
Numeric buttons: Switches the channel in Live TV
mode, enters a number or a letter in the text box on
the screen
3.
Language: Switches among sound modes (analogue
TV), displays and changes audio language (digital TV,
where available)
4.
Volume +/-
5.
Microphone: Activates the microphone on the remote
6.
Home: Opens the Home Screen
7.
Guide: Displays the electronic programme guide in
Live TV mode
8.
OK: Confirms selections, enters sub-menus, views
channel list (in Live TV mode)
9.
Back/Return: Returns to previous menu screen, goes
one step back, closes open windows, closes teletext (in
Live TV-Teletext mode)
10. Net ix: Launches the Net ix application
11. Prime Video: Launches the Amazon Prime Video
application
12. Menu: Displays Live TV Settings menu (in Live TV
mode), displays available setting options such as sound
and picture
13. Rewind: Moves frames backwards in media such as
movies
14. Stop: Stops the media being played
15. Record: Records programmes in Live TV mode
16. Coloured Buttons: Follow the on-screen instructions for
coloured button functions
17. Pause: Pauses the media being played, starts timeshift
recording in Live TV mode
Play: Starts to play selected media
18. Text: Opens and closes teletext (where available in
Live TV mode)
19. Fast forward: Moves frames forward in media such
as movies
20. Source: Shows all available broadcast and content
sources, is also used in pairing process of the remote.
21. Google Play: Launches the Google Play Store appli-
cation
22. YouTube: Launches the YouTube application
23. Exit: Closes and exits from Live TV Settings menus,
closes the Home Screen, exits from any running
application or menu or OSD banner, switches to last
set source
24. Directional buttons: Navigates menus, setting options,
moves the focus or cursor, etc. sets record time and
displays the subpages in Live TV-Teletext mode when
pressed Right or Left. Follow the on-screen instructions.
25. Info: Displays information about on-screen content
26. Programme +/-: Increases/Decreases channel number
in Live TV mode
27. Mute: Completely turns o the volume of the TV
28. Subtitles: Turns subtitles on and o (where available)
Standby Button
Press and hold the Standby button on the remote
control. Power o dialogue will appear on the screen.
Highlight OK and press the OK button. The TV will
switch into standby mode. Press brie y and release
to switch the TV into quick standby mode or to switch
on the TV when in quick standby or standby mode.
English - 8 -
Publicidad
