Publicidad
Idiomas disponibles
Idiomas disponibles
14. TheTable Sawis designed f orhomeuseor light
27. NEVER perform layout, a ssembly orset-upworkon
commercial dutyONLY.
thetable/work a reawhenthemachine is running.
15. CONNECT T able Sawtoa properly grounded o utlet
only. S eegrounding instructions.
28. NEVER resetthethermal-overload buttonbefore
youhaveturned thetablesaw"OFF".
16. ALWAYS USEtheguards whenever possible.
Check toseethattheyarein place,secured and
working correctly.
17. AVOID KICKBACK by:
• Keeping bladesharpandfreeof rustandpitch.
• Keeping ripfenceparallel to sawblade.
• Using sawbladeguard andsplitterassembly f or
everypossible operation, including allthrough-
sawing.
• Pushing theworkpiece p astthesawbladepriorto
release.
• Neverripa workpiece t hatis twisted or
warped, or doesnothavea straight e dgetoguide
alongthefence.
• Using featherboards whenthebladeguard and
splitter a ssembly cannot b eused.
Never s awinga largeworkpiece t hatcannotbe
controlled.
Neverusingthefenceas a guidewhencross-
cutting.
• Never s awinga workpiece w ithlooseknots or
otherflaws.
18. REMOVE cut-off p ieces anddebris fromthetable
before starting thesaw. Thevibration ofthesaw
maycause themto moveintothesawbladeandbe
thrown out. Aftercutting, t urnthesawoff. When
thebladehascometoa complete s top,unplug the
sawandremove alldebris.
19. NEVER START thesawwiththeworkpiece against
theblade.
20. NEVER perform "free-hand" operations. U seeither
thefenceor mitergauge to position andguidethe
workpiece. Holdtheworkpiece f irmlyagainst t he
mitergaugeor fence.
21. USEa pushstick(s) f or ripping a narrow workpiece.
22.
AVOID AWKWARD OPERATIONS AND HAND
POSITIONS where a sudden slip could cause a
hand to move into the blade.
23. KEEP arms, hands and fingers away from the
blade.
24. NEVER have any part of your body in line with the
path of the saw blade.
25. NEVER reach around or over the blade.
26. NEVER attempt to free a stalled blade without first
turning the machine "OFF" and unplugging it from
the power source.
29.
30.
31.
32.
33.
34.
PROPERLY SUPPORT long or wide workpiece.
TURN THE SAW "OFF" and unplug from power
source.
Clean off the table/work area before leav-
ing the saw. LOCK the START/STOP switch with
padlock provided to prevent unauthorized use.
ALWAYS position auxiliary fence at least 2-inches
in front of saw blade when using auxiliary fence as
a stop when cross-cutting.
The right extension wing MUST BE completely
assembled and motor cover closed and fastened
before table saw is to be connected to the power
source.
ADDiTiONAL
iNFORMATiON
regarding the safe
and proper operation of this product is available
from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201 in the Accident
Prevention Manual for Industrial Operation and also
in the Safety Data Sheets provided by the NSC.
Please also refer to the American National
Standards Institute ANSi 01.1 Safety Requirements
for Woodworking
Machinery and the U.S.
Department of Labor OSHA 1910.213 Regulations.
SAVE THESE iNSTRUCTiONS.
Refer to them
frequently and use them to instruct other users.
Information regarding the safe and proper operation of
this tool is available from the following sources:
Power Tool Institute
1300 Summer Avenue
Cleveland, OH 44115-2851
www.powertoolinstitute.org
National Safety Council
1121 Spring Lake Drive
Itasca, IL 60143-3201
American National Standards Institute
25 West 43rd Street
4th floor
New York, NY 10036
www.ansi.org
ANSi 01.1 Safety Requirements for Woodworking
Machines, and the U.S. Department of Labor regulations
www.osha.gov
Publicidad
