Bosch GAS 18V-10 L Professional Manual Original página 17

Technical data
Cordless wet/dry vacuum cleaner
Article number
Voltage
Rated power input
Container volume (gross)
Net volume (liquid)
A)
Max. vacuum
B)
– Dust extractor
– Turbine
A)
Max. flow rate
B)
– Dust extractor
– Turbine
Operating time per battery
charge
Dust class
Weight according to EPTA-Pro-
cedure 01:2014
Protection rating
Recommended ambient tem-
perature during charging
Permitted ambient temperature
D)
during operation and during
storage
Recommended rechargeable
batteries
Recommended chargers
A) Measured at 20–25 °C with rechargeable
battery GBA 18V 6.3Ah
B) Measured with vacuum hose (13) and curved nozzle (15)
C) Depends on battery in use
D) Limited performance at temperatures < 0 °C
Values can vary depending on the product, scope of application and
environmental conditions. To find out more, visit
www.bosch-professional.com/wac.
Noise/Vibration Information
Noise emission values determined according to
EN 60335‑2‑69.
Typically the A-weighted sound pressure level of the dust ex-
tractor is 79 dB(A). Uncertainty K = 2 dB. The noise level
when working can exceed the volume stated. Wear hearing
protection!
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 60335‑2‑69:
2 2
a < 2.5 m/s , K = 1.5 m/s .
h
Bosch Power Tools
Rechargeable battery
GAS 18V-10 L
Bosch sells some cordless dust extractors without a re-
chargeable battery. You can tell whether a rechargeable bat-
3 601 JC6 3..
tery is included with the dust extractor by looking at the
V 18
packaging.
W 260
Charging the battery
l 10
l 6
u
hPa 90
Note: Lithium-ion rechargeable batteries are supplied par-
hPa 115
tially charged according to international transport regula-
tions. To ensure full rechargeable battery capacity, fully
charge the rechargeable battery before using your tool for
l/s 24
the first time.
m³/h 86
l/s 34
Inserting and Removing the Battery
m³/h 122
(see figures A1−A2)
min/Ah 4
u
L
C)
kg 5,1–6,1
u
– Press the release button (11) to open the battery com-
IPX4
°C 0 ... +35
– Slide the battery (20) into the battery bay (19) until it
°C –20 ... +50
– To remove the battery (20), press the release
GBA 18V...
– Close the battery compartment cover (12).
ProCORE18V...
GAL 18...
Changing the Battery Compartment Cover
GAX 18...
(see figures A3−A5)
GAL 36...
If you wish to use a ProCORE18V 12Ah battery, the battery
compartment cover (12) can then no longer be closed. In
this case, the battery compartment cover (12) can be re-
placed with a screen (23) designed for this purpose.
In damp or wet conditions, the dust extractor may only be
used with the battery compartment cover closed.
Removing the Battery Compartment Cover
(see figure A3)
Remove the battery (20) from the battery bay (19).
Remove the two fastening screws (22) (ST4×12) with a
cross-headed screwdriver PH1 and take off the battery com-
partment cover (12).
Inserting the Screen (see figure A4)
Press the battery compartment cover bracket (24) down-
wards and slide on the screen (23).
Removing the Screen (see figure A5)
Apply a slot screwdriver, push the screen (23) a little way to-
wards the rear and remove the screen. When doing so, press
the battery compartment cover bracket (24) downwards.
Use only the chargers listed in the technical data. Only
these chargers are matched to the lithium-ion battery of
your dust extractor.
Do not use force to insert the battery. The battery is de-
signed in such a way that it can only be inserted into the
product when it is in the right position.
Keep the battery compartment and the battery bay clean
and dry at all times to ensure good, safe operation.
partment cover (12).
audibly clicks into place.
button (21) on the battery and pull it out of the battery
bay (19).
1 609 92A 98S | (10.01.2024)
English | 17