Publicidad
Idiomas disponibles
Idiomas disponibles
16 | English
Removing the planer blade (see figure B)
To turn or replace the planer blade (16), turn the blade head
(13) until it is parallel to the planer base plate (10).
➊ Loosen the two fastening screws (15) using the hex key
(12) (approx. 1–2 turns).
➋ If necessary, loosen the clamping element (14) by
lightly striking it with an appropriate implement, e.g. a
wooden wedge.
➌ Use a piece of wood to push the planer blade (16) to
the side and out of the blade head (13).
Fitting the planer blade (see figure C)
The guide groove on the planer blade ensures a constant,
even height setting when changing or turning the blade.
If necessary, clean the knife seat in the clamping element
(14) and the planer blade (16).
When fitting the planer blade, ensure that it is securely
seated in the mounting guide of the clamping element (14)
and is aligned flush with the side edge of the planer base
plate (10) at the rear. Then tighten the two fastening screws
(15) with the hex key (12).
Note: Check that the fastening screws (15) are firmly
tightened before starting operation. Turn the blade head
(13) by hand and ensure that the planer blade is not brush-
ing against anything.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Clean the chip ejector (1) regularly. Clean a clogged chip
ejector using a suitable tool, e.g. a piece of wood, com-
pressed air, etc.
Do not allow the chip ejector to come into contact with
u
your hands. You may be injured by rotating parts.
Always use an external dust extraction device or chip/dust
bag to guarantee optimum suction.
External dust extraction (see figure D)
An extraction hose (dia. 35 mm) (17) (accessory) can be
connected to the chip ejector on either side.
1 609 92A 5TN | (23.06.2020)
Connect the dust extraction hose (17) to a dust extractor
(accessory). You will find an overview of how to connect to
various dust extractors at the end of these operating instruc-
tions.
The dust extractor must be suitable for the material being
worked.
When extracting dry dust that is especially detrimental to
health or carcinogenic, use a special dust extractor.
Self-generated dust extraction (see figure D)
A chip/dust bag (accessory) (18) can be used for smaller
jobs. Insert the dust bag nozzle of the chip/dust bag firmly
into the chip ejector (1). Empty the chip/dust bag (18) at
regular intervals to maintain optimum dust collection.
Selectable chip ejector
Using the changeover lever (4), the chip ejector can be (1)
adjusted to the right or left. Push the changeover lever (4) all
the way towards the end position until it clicks into place.
The selected chip ejector direction is indicated by an arrow
symbol on the changeover lever (4).
Operation
Start-up
Inserting the battery
Insert the charged battery (7) into the battery holder until it
is flush and you feel it engage.
Switching on/off
Make sure that you are able to press the On/Off switch
u
without releasing the handle.
To start the power tool, first press the lock-off switch (5),
then press and hold the on/off switch (6).
To switch off the power tool, release the on/off switch (6).
Note: For safety reasons, the on/off switch (6) cannot be
locked; it must remain pressed during the entire operation.
Run-out brake
An integrated run-out brake shortens the time the cutter
shafts keep running for after the power tool has been
switched off.
Setting the cutting depth
Using the knob (2), the cutting depth can be continuously
adjusted between 0–1.6 mm with the aid of the cutting
depth scale (3).
Practical advice
Planing Procedure
Set the required cutting depth and position the power tool
with the front section of the planer base plate (10) on the
workpiece.
Only bring the power tool into contact with the work-
u
piece when switched on. Otherwise there is danger of
kickback if the cutting tool jams in the workpiece.
Switch on the power tool and guide it over the surface of the
workpiece, applying uniform feed.
Bosch Power Tools
Publicidad
