Publicidad
Idiomas disponibles
Idiomas disponibles
9.6
Test run (Fig. 1)
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal nois-
es are heard.
1. Before operation, check whether the tool attach-
ment is properly attached, i.e. centred in the quick-
release chuck (2).
2. Screw bits are marked with their dimensions and
shape. If you are unsure, always try out first wheth-
er the bit sits in the screw head without play.
9.7
Gear selection (Fig. 1)
1. Push the gear selector switch (4) to 1
sponding to a low or high speed selection.
Gear 1 :
Suitable for:
Rotational speed:
Torque:
Gear 2 :
Suitable for:
Rotational speed:
Torque:
9.8
Set direction of rotation
ATTENTION
The direction of rotation switch may only be actuated
when idle.
With the direction of rotation switch, you can select the
direction of rotation of the product (clockwise or anti-
clockwise) and secure the product from being switched
on unintentionally. The arrow on the direction of rotation
switch indicates the working direction.
1. Wait until the product has come to a standstill.
2. Push the direction of rotation switch (10) to the de-
sired position:
– Clockwise rotation: For drilling and screwing
in screws. Press the direction of rotation switch
to the right.
– Anti-clockwise rotation: To undo screws.
Press the direction of rotation switch to the left.
3. Switch lock: Put the direction of rotation switch in
the centre position.
9.9
ATTENTION
The torque adjusting ring may only be actuated when
idle.
Note:
A clear ratcheting sound is heard when reaching the
preset torque limit. This noise is caused by the slip
clutch.
Note:
You can preset the maximum torque by turning the
torque adjusting ring (3) and, by turning the mode se-
lection adjusting ring (3a), select the screw setting
or 2 corre-
drill setting
torque levels + 1 screw setting + 1 drill setting + 1 ham-
mer-drill setting.
0 - 400 rpm
• Select a low level for small screws or soft materials.
Screwing work
• Select a high level for large screws, hard materials
Low
or when unscrewing screws.
High
• For drilling work, select the drill setting by adjusting
the mode selection adjusting ring (3a) into position .
0 - 1550 rpm
• For percussion drilling, select the percussion level
Drilling work
by turning the mode selection ring (3a) to the posi-
High
tion
Low
Requirement:
Screws:
Drilling:
Hammer-drilling: -
9.10
The speed can be steplessly controlled by the on/off
switch. The further you press the on/off switch, the
higher the speed.
1. To switch on the product, push the on/off switch (9).
2. To switch off, release the on/off switch (9).
If you put the direction of rotation switch (10) in the
centre position, the product is secured from being
switched on.
9.10.1
This product is equipped with an LED work lamp to illu-
minate the immediate work area and improve visibility
in poorly lit environments.
Do not look directly into the LED work lamp or the
light source.
1. The LED work lamp (8) lights up automatically as
soon as the product is switched on.
www.scheppach.com
Adjusting the torque / Selecting
the operating mode (Fig. 1)
and hammer-drill setting
.
Torque
Level 1 - 25 Screw setting
-
On/Off switch (9) (Fig. 1)
LED work lamp (8) (Fig. 1)
CAUTION
. There are 25
Operating mode:
Drill setting
Hammer-drill setting
GB | 29
Publicidad
