ANSMANN WFL10W Manual De Instrucciones página 6

away from the lamp.
• Use the product exclu-
sively with the acces-
sories included with it.
• Do not short-circuit
connection terminals or
batteries.
triangleDANGER OF FIRE AND
EXPLOSION
• Do not use while still in
the packaging.
• Do not cover the pro-
duct - risk of fire.
• Never expose the pro-
duct to extreme condi-
tions, such as extreme
heat/cold etc.
• Do not use in the rain or
in damp areas.
circle-c GENERAL INFORMATION
• Do not throw or drop
• The LED cover cannot be replaced. If the
cover is damaged, the product must be
disposed of.
• The LED light source cannot be replaced. If
the LED has reached the end of its service
life, the complete lamp must be replaced.
• Do not open or modify the product! Repair
work shall only be carried out by the manu-
facturer or by a service technician appointed
by the manufacturer or by a similarly qualified
person.
• Disconnect the device from the power supply
only by pulling on the plug or plug housing,
never on the cable.
• Information for the light and mains adapter
as well as mains voltage on the socket must
match with the type plate.
• The lamp shall not be placed face-down or
allowed to topple face-down.
circle-c ENVIRONMENTAL INFORMATION |
DISPOSAL
Dispose of packaging after sorting by material
type. Cardboard and cardboard to the waste
paper, film to the recycling collection.
Dispose of the unusable product in accor-
dance with legal provisions. The "waste
bin" symbol indicates that, in the EU, it is
not permitted to dispose of electrical equip-
ment in household waste.
For disposal, pass the product on to a spe-
cialist disposal point for old equipment, use the
return and collection systems in your area or
contact the dealer from whom you purchased
the product.
10 GB
DE | | FR | ES | PT | SE | IT | NL | DK | FI | NO | PL
‫ ׋‬PART DESCRIPTION
1. LED's
2. Hinge (360° tilt able)
3. Cable connector
4. Mounting bracket
circle-c LIABILITY DISCLAIMER
The information contained within these
operating instructions can be changed without
prior notification. We accept no liability for
direct, indirect, incidental or other damage or
consequential damage arising though improper
handling/use or through disregard of the
information contained within these operating
instructions.
‫ ׋‬INSTALLATION INSTRUCTIONS
Note! Only a VDE-certified waterproof cable
H05RN 3×1.0mm2 or H07RN-F 3×1.0mm2 or
better may be used for the connection.
Other light sources (e.g. lanterns) can impair
the function of the sensor. Do not install the
product within the effective range of other light
sources.
‫ ׋‬INSTALLATION
The fixing holes in the bracket have a diameter
of 6 mm. Select suitable mounting material
for this.
The mounting materials are not supplied. As an
example, these instructions show installation
with two screws and two dowels. Other moun-
ting materials can be used as required.
Disconnect the power supply to the cable at
the fuse box and secure against reconnection
by third parties. (Fig. 01)
Determine the installation location and mark
the wall. (Fig. 02.1)
Drill holes at the marked points with an electric
drill. (Fig. 02.2)
Insert the dowels into the drilled holes. (Fig.
02.3)
Remove the nut of the quick connector. (Fig.
02.4)
Feed the mains cable through the nut and
connect it to the housing. The length of the
stripping head and the immersion tube is 8 mm.
(Fig. 02.5)
Connect the wires to the respective terminals:
Blue wire to N (neutral)
Brown cable to L (phase)
Green/yellow cable to PE (earth) (Fig. 02.6)
Tighten the plug. (Fig. 02.7)
Tighten the nut. (Fig. 02.8)
Fix the screws, washers and brackets to the
mounting holes. (Fig. 02.9)
Tighten the screws of the mounting bracket
using a suitable tool. (Fig. 02.10)
Switch the fuse box back on. (Fig. 03)
‫ ׋‬ADJUSTING THE SPOTLIGHT
The lamp can be angled 90 degrees downwards
and 45 degrees upwards. (Fig. 03)
‫ ׋‬CLEANING
Disconnect the power supply from the product
at the switch cabinet before any cleaning.
Secure the product to prevent it being uninten-
tionally reactivated by attaching a warning sign
at the switch cabinet.
Use only a soft, dry or slightly moist cloth (with
a little mild washing-up liquid if required).
Do not use abrasive agents or solvents for
cleaning.
Subject to technical changes. We assume no liability for printing errors.
GB
DE | | FR | ES | PT | SE | IT | NL | DK | FI | NO | PL
11