Publicidad
Idiomas disponibles
Idiomas disponibles
All manuals and user guides at all-guides.com
NOTE: If you have charged the battery
and it still will not start your car, do not
use the Engine Start feature, or it will
damage the vehicle's electrical system.
Have the battery checked.
1. Set the switch to the OFF position.
2. With the charger unplugged from the
AC outlet, connect the charger to the
battery following the instructions given
in Charging a Battery in the Vehicle.
3. Plug the charger AC power cord into
the AC outlet.
4. With the charger plugged in and
connected to the battery of the vehicle,
set the ON/OFF switch to the Engine
Start position. The Engine Start LED
will illuminate.
5. Crank the engine until it starts. If
engine does not start within 5
seconds, wait 45 seconds before
trying again. NOTE: After 3 minutes in
ENGINE START mode, unit will enter
into a COOL-DOWN period of 180
seconds to allow the charger and the
battery to cool down.
NOTE: During extremely cold weather,
or if the battery is under 2 volts, boost
the battery for 5 minutes or more before
cranking the engine.
6. If the engine fails to start, use the
40A Boost rate for 5 minutes before
attempting to crank the engine again.
7. After the engine starts, move the switch
to the OFF position and unplug the AC
power cord before disconnecting the
battery clips from the vehicle.
8. Clean and store the charger in a dry
location.
NOTE: If the engine does turn over but
never starts, there is not a problem with
the starting system; there is a problem
somewhere else with the vehicle. STOP
cranking the engine until the other problem
has been diagnosed and corrected.
BATTERY CHARGING TIMES
BATTERY
APPLICATION
SIZE
POWERSPORTS
6Ah
32Ah
AUTOMOTIVE
300 CCA
1000 CCA
MARINE
50Ah
105Ah
Times are based on a 50% discharged
battery and may change, depending on age
and condition of battery.
CHARGING TIME (Hours)
6A
10A
20A
30A
2
1. 5
. 5
. 5
5
4
1. 5
1
4
3
1. 5
1. 5
10
7
3.5
3
5
3.5
1. 5
1
11
8
4
3
AUTOMATIC CHARGING MODE
When an Automatic Charge is performed,
the charger switches to the maintain mode
automatically after the battery is charged.
ABORTED CHARGE
If charging cannot be completed normally,
charging will abort. When charging aborts,
the charger's output is shut off and the
BOOST/CHARGING (yellow/orange) LED
will flash. Do not continue attempting to
charge this battery. Check the battery
and replace, if necessary.
DESULFATION MODE
Desulfation could take 8 to 10 hours. If
desulfation fails, charging will abort and the
BOOST/CHARGING (yellow/orange) LED
will flash.
COMPLETION OF CHARGE
Charge completion is indicated by the
CHARGED/MAINTAINING (green) LED.
When pulsing, the charger has switched to
the maintain mode of operation.
MAINTAIN MODE
(FLOAT MODE MONITORING)
When the CHARGED/MAINTAINING
(green) LED is pulsing, the charger has
started maintain mode. In this mode, the
charger keeps the battery fully charged
by delivering a small current when
necessary. If the charger has to provide
its maximum maintain current for a
continuous 12 hour period, it will go into
abort mode (see Aborted Charge section).
This is usually caused by a drain on the
battery or the battery could be bad. Make
sure there are no loads on the battery. If
there are, remove them. If there are none,
have the battery checked or replaced.
MAINTAINING A BATTERY
The BE01252 charges and maintains
12 volt batteries, keeping them at full
charge.
NOTE: The maintain mode technology
allows you to safely charge and maintain
a healthy battery for extended periods
of time. However, problems with the
battery, electrical problems in the
vehicle, improper connections or other
unanticipated conditions could cause
excessive current draws. As such,
occasionally monitoring your battery and
the charging process is required.
• 7 •
Publicidad
