Publicidad
Idiomas disponibles
Idiomas disponibles
GB
CARRIER TRACK
INSTRUCTIOIN FOR USE
A.1
ADJUST THE HEIGHT OF THE HANDLE
A
Press the handle adjustment button and
the corresponding gear. (Press the handle adjustment button on both sides at the same time
during operation)
1. Used for installation in cars.
2. The portable handle adjustment button is pressed for lifting and movinggthe seat.
3. Usedas cradle mode, used for rocking to coax children to sleep.
4. As nursing or rest after the used of sleeping position, used to support the seat, in order to
achieve the effect of not tilting.
• Make sure the handle is fully locked in the appropriate gear when using.
A.2
THE USAGE OF THE Y-SHAPE BELT BUCKLE
Step 1_Press the red button of the buckle to open the buckle.
Step 2_ Close the left and right inserts together and insert them into the buckle until the sound
of "click" is heard and the table is completely buckled.
A.3
ADJUST THE TIGHTNESS OF THE Y-SHAPE BELT
• Release the seat belt
PRESS the seat belt adjusting button, grab the two straps by hand and pull them down to
lengthen the straps and release the seat belt.
• D'ont pull the shoulder pad ! Tighten Y- shape Belt after placing the child in the child seat,
fasten the buckle and pull adjusting strap.
• Tighten the Y-shape belt until it is adjusted to the child - friendly tightness.
A.4
ADJUST THE HEIGHT OF THE SHOULDER BELT BY USAGE OF SMALL BABY
INSERT CUSHION
• Place your child in the child seat and check that the top of the shoulder strap should be slightly
higher than the baby's shoulder. The correct shoulder strap position is shown in the figure A.4
• The small baby insert cushion is used only when the child's height is less than 60 cm.
A.5
PLACE THE CHILD IN THE CHILD SEAT
Step 1_Open the buckle, spread the clips on both sides, then put the child in the seat.
Step 2_Ajust the headrest of child seat in order that the shoulder belt is at the right position:
( refer to item A:4 )
Step 3_Fasten the buckle and tighten the adjusting strap according to item A:3
A.6
INSTALLATION IN THE CAR
Step 1_ Put the child seat on the vehicle seat in rearward facing direction, adjust the handle to
position
according to item A.1
2
Step 2_ Pull out the vehicle safety belt to keep the child seat in place. Firstly, pass the lab belt
through the lab belt guide on both sides of the child seat.
Step 3_ Secondly, lead the shoulder belt through the shoulder belt guide hooks at the back of the
child seat.
Step 4_ Fasten the vehicle safety belt buckle.
Step 5 _ Tighten the vehicle safety belt.
Step 6_ Adjust the handle to position
B.1
THE DISASSEMBLY AND INSTALLATION OF THE COVER
Step 1_ Use the tool to remove the guide hooks on both sides of the child seat.
Step 2_ Remove the headrest mattress from the child seat.
Step 3_ Remove the canopy cover.
Step 4_ Remove the canopy strip.
20
1
turn the handle forward or backward to
1
according to item A.1
GB
CARRIER TRACK
B.2
CLEAN THE CHILD SEAT COVER
The child seat cover can be cleaned with clean water of 30º℃℃ then to dry.
2
fix
WARNING: Cloth cover is an important part of the child safety seat.
Do not use child safety seat without cloth cover,and do not use other products to replace the
original cloth cover.
30º C
C
INSTALLATION IN THE CAR
This child seat is only applicable if the applicable
model is equipped with the ECE R16 three-point seat belt requirement.
A
B
INFORMATION ABOUT THE GUARANTEE
- This item is guaranteed against manufacturing defects as stipulated in the legal Directives
and/or regulations in force on guarantees for consumer goods applicable to the European
Union and those of the country in which it is marketed.
- It is essential to present the purchase invoice or receipt in order to process the guarantee
through the seller of the item or, failing that, through the manufacturer.
- The guarantee excludes anomalies or faults caused by misuse, non-compliance with the
safety regulations and instructions for use and maintenance provided, or due to wear and
tear caused by normal use and regular handling of the item.
- The label containing the serial number of your model must not be torn off under any cir-
cumstances as it contains information relevant to the guarantee.
MAINTENANCE
Keep the metal parts clean and dry to prevent rusting.
Regularly grease the mobile parts and mechanisms with a silicone-based spray. Do not use oil or
grease. Only use mild detergent and warm water to clean the plastic parts.
Do not expose the upholstery to sunlight for prolonged periods of time. The upholstery can be
taken off and washed.
A_ Diagonal belt
B_ Lap belt
A
Do not place in the front seat with an airbag.
Only if it's equipped with an adult an adult 3-point belt.
IMPORTANT REMINDING
B
It is important to note that this car child safety seat can
only be installed in the vehicle with three-point vehicle
safety belt.
WARNING: DO NOT use on a passenger
seat with a front airbag!
A
B
21
Publicidad
