Parkside PABSP 20 LI C3 Guía Rápida página 34

This product is equipped with an automatic spindle lock to open
or close the chuck with the chuck ring
1 ] [
Open the chuck : Turn the chuck ring
[ 1 ]
clockwise direction (Fig. E).
Insert a suitable accessory tool into the chuck
as required.
Close the chuck : Hold the accessory tool in position.
1 ] [
Turn the chuck ring in a clockwise direction.
2 ] [
NOTE
This product is equipped with a Röhm drill chuck with an
u
anti-lock function.
If you attempt to open the fully opened chuck
u
the anti-lock function will be activated to protect the
chuck.
When the anti-lock function is activated, the chuck
u
cannot be closed by turning the chuck ring
clockwise direction. A ratcheting sound will be produced
when you attempt to close the chuck.
Deactivating the chuck's
u
the chuck ring in a clockwise direction by a certain
[ 2 ]
extent. Then, turn the chuck ring
quickly in a counter-clockwise direction.
Repeat this action if the anti-lock function is still active.
When the anti-lock function is deactivated, you should
be able to close the chuck
˜ Trial run
NOTE
Always carry out a no-load trial run before starting work
u
and after every accessory tool replacement. Switch
the product off immediately if the accessory tool is not
running smoothly, if considerable vibration occurs or if
you hear abnormal noises.
Before operating the product, check whether the accessory
tool is correctly positioned, i.e. centred in the chuck
Screw bits are labelled according to their dimensions and
their shape. If you are uncertain, always check whether the
bit fits tightly in the screw head without any free play.
˜ Operation
˜ Gear selection
m
ATTENTION! RISK OF PRODUCT DAMAGE!
Do not operate the gear selector
product has come to a standstill.
Change the gear by sliding the gear selector
or backwards (fig. F).
34 GB/IE
.
[ 2 ]
in a counter-
2 ] [
as deep
[ 1 ]
further,
[ 1 ]
1 ] [
in a
[ 2 ]
anti-lock function: Turn
1 ] [
suddenly and
[ 2 ]
without ratcheting sounds.
[ 1 ]
.
1 ] [
until the
[ 4 ]
forwards
4 ] [
1 gear:
st
Suitable for:
Speed:
Torque:
2 gear:
nd
Suitable for:
Speed:
Torque:
˜ Setting the rotating direction
m
ATTENTION! RISK OF PRODUCT DAMAGE!
Do not operate the rotation direction switch
until the product has come to a standstill.
Change the direction of rotation by pressing the rotation
direction switch towards the left or right (fig. G).
[ 5 ]
When the rotation direction switch
position, the on/off switch
˜ Torque control
This product is equipped with a torque control that disengages
the spindle when a predefined torque is exceeded.
The torque can be adjusted by turning the torque sleeve
(fig. H).
Small screws or soft materials: Select a low level.
Large screws, hard materials or removing screws: Select a
high level.
For drilling operation: Turn the torque sleeve
position.
˜ Switching on and off
NOTE
The on/off switch cannot be locked.
[ 6 ]
u
Switching on: Press and hold the on/off switch
Regulate the speed as required (see "Speed control")
(fig. I).
Switching off: Release the on/off switch
˜ Speed control
By using the on/off switch
control the speed:
Pressure
Gentle pressure:
Greater pressure:
Screwing
Low
High
Drilling
High
Low
[ 5 ]
is in the middle
[ 5 ]
is locked.
[ 6 ]
to the
3 ] [
.
6 ] [
.
6 ] [
, you can progressively
[ 6 ]
Speed
Lower speed
Higher speed
3 ] [