Descargar Imprimir esta página

DeWalt DWE397 Traducido De Las Instrucciones Originales página 22

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 26
EngLIsh
b ) Use clamps or another practical way to secure and
support the workpiece to a stable platform. Holding
the workpiece by hand or against your body leaves it
unstable and may lead to loss of control.
Plugging into the mains, switching ON and
OFF
Always ensure that the alligator saw is switched OFF before
plugging into the mains.
After switching OFF, never attempt to stop the saw blades with
your fingers.
Never put the saw down on a table or work bench unless
switched OFF. The saw blades will keep running up to
10 seconds after the machine has been switched OFF.
When sawing
Remove all nails and metal objects from the workpiece before
starting work.
Wherever possible, use clamps and vices to fasten the
workpiece securely.
Do not attempt to saw extremely small workpieces.
Do not bend too far forward. Make sure that you always stand
firmly, particularly on scaffolding and ladders.
Always hold the saw with both hands.
Do not use the saw for cutting curves and pockets.
Checking and changing the saw blades
Unplug the tool before cleaning or changing the saw blades.
Only use D
WALT saw blades conforming to the specifications
e
contained in these operating instructions.
Only sharp saw blades in perfect working condition should
be used; cracked or bent saw blades should be discarded and
replaced at once.
Always use suitable gloves when handling the saw blades and
rough work materials.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA or less.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
Impairment of hearing.
Risk of personal injury due to flying particles.
Risk of burns due to accessories becoming hot
during operation.
Risk of personal injury due to prolonged use.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the power supply corresponds to the voltage
on the rating plate.
Your D
WALT tool is double insulated in accordance
e
with EN62841; therefore no earth wire is required.
20
If the supply cord is damaged, it must be replaced by a
specially prepared cord available through the D
service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in the plug.
Connect the blue lead to the neutral terminal.

WARNING: No connection is to be made to the
earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1.5 mm
is 30 m.
When using a cable reel, always unwind the cable completely.
Package Contents
The package contains:
1 Alligator saw
1 TCT saw blade set for low density building block (DWE396,
DWE397)
1 TCT saw blade set for medium density building block
(DWE398)
1 TCT saw blade set for cellular concrete and plaster board
(DWE399)
1 Hex key
1 Cutting slot scraper (DWE399 only)
1 Instruction manual
Check for damage to the tool, parts or accessories which may
have occurred during transport.
Take the time to thoroughly read and understand this manual
prior to operation.
Markings on Tool
The following pictograms are shown on the tool:
Read instruction manual before use.
Wear ear protection.
Wear eye protection.
Do not expose the power tool to humidity.
Do not use the power tool if the main cable
is damaged.
WALT
e
; the maximum length
2

Publicidad

loading

Este manual también es adecuado para:

Dwe396Dwe398Dwe399Dwe397-qs