Publicidad
Idiomas disponibles
Idiomas disponibles
1. Unhook the grass collection basket and brush it out
with a hand brush. You can also roughly clean the
housing of the lawnmower with the sweeper.
2. Clean the underside of the lawnmower with a spatula
and hand brush. The spatula helps to remove coarse
and larger plant debris from the area of the blade (19).
Cleaning the underbody is easier and more thorough
immediately after use. Then dirt and plant residues
are still fresh and can be loosened more easily.
3. Do not use any cleaning products or solvents; they
could attack the plastic parts of the product. Make
sure that no water can penetrate the product interior.
4. Check that the grass ejection is clear of grass resi-
dues and remove these if necessary.
11.2
Maintenance
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
11.2.1
Changing the blade (16) (Fig. 19)
WARNING
There is a risk of injury if you work with a
damaged blade.
–
Wear protective gloves!
–
For safety reasons you should only ever have your
blade sharpened and balanced by an authorised
specialist workshop. For optimum results it is rec-
ommended that the blade should be inspected once
a year.
–
When changing the blade, only use original spare
parts.
1. Hold the blade (16) tightly with one hand.
2. Turn the blade screw (15) anticlockwise using a
13 mm open-ended spanner (not included in the
scope of delivery).
3. Remove the blade screw (15) and the washer.
4. Re-install the new blade (16) in reverse order. Fasten
the blade screw (15) properly. Ensure that the blade
(16) is correctly positioned in the fastening pins and
lies flush.
5. The tightening torque of the blade screw (15) is
45Nm. Also replace the blade screw (15) when replac-
ing the blade (16).
11.2.2
Damaged blade (16) (Fig. 19)
If the blade (16) has come into contact with an obstacle:
• Switch off the motor, wait for it to stop, remove the
battery and pull out the safety key.
• Check the blade (16) for damage.
• Damaged or bent blades (16) must be replaced.
• Never attempt to bend a bent blade (16) back to
straight again.
30 | GB
• Never mow the lawn with a bent or heavily worn blade
(16) as this will cause vibrations and can lead to fur-
ther damage to the lawnmower.
12 Storage and transport
Store the product and its accessories in a dark, dry and
frost-free place that is inaccessible to children.
The optimum storage temperature is between 5°C and
30˚C.
Store the product in its original packaging.
Cover the product to protect it from dust or moisture.
Store the operating manual with the product.
WARNING
Danger of injury!
Remove the battery from the power tool before carrying
out any work on the power tool (e.g. maintenance, tool
change, etc.) and when transporting and storing it.
There is a risk of injury if the on/off switch is operated
unintentionally.
12.1
Fold the upper push bar (2)
together (Fig. 1, 7, 13)
WARNING
Risk of jamming!
Always hold the push bar with one hand at the highest
point.
–
Never place fingers between the upper push bar
and the lower push bar.
For space-saving storage, the upper push bar (2) is fold-
able.
1. Remove the grass collection basket (5).
2. Open the quick-clamp levers (2c) on the upper push
bar (2).
3. Loosen the quick-clamp lever (2c) a little by turning it
anti-clockwise.
4. Move the upper push bar (2) down. The cable (10)
must not be pinched in the process.
12.2
Preparation for storage
1. Remove the battery.
2. Empty the product completely.
3. Clean and check the product for damage.
13 Repair & ordering spare parts
With this product, it is necessary to note that the following
parts are subject to natural or usage-related wear, or that
the following parts are required as consumables.
ATTENTION
According to the German Product Liability Act, no liabili-
ty is accepted for damage caused by improper repairs
or by not using original spare parts.
Such work should be performed by a customer service
centre or an authorised specialists. The same applies to
accessory parts.
www.scheppach.com
Publicidad
