Descargar Imprimir esta página

Silverline 870944 Manual Del Usuario página 7

Lijadora orbital 240 w
Ocultar thumbs Ver también para 870944:

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 22
Switching on and off
WARNING: Always wear safety goggles, an adequate dust mask, hearing protection and suitable
gloves, when working with this tool.
WARNING: Never switch the sander on when the base is in contact with the workpiece or
any other surface, as this might cause the operator to lose control over the machine, and lead to
serious injury.
1. Connect the Power Cord (4) to the mains power supply
2. Push the On/Off Switch (2) in to the 'I' position, to switch the sander 'on'
3. To switch 'off' the sander, push the On/Off switch in to the 'O' position
WARNING: Always wait until the machine has stopped vibrating completely before putting it
down. Always disconnect from the power supply after use.
Sanding
If the tool is connected to a vacuum dust extraction system, switch the extraction device 'on'
before switching on the sander. Switch the sander 'off' first, then the vacuum system
Move the machine in a circular motion over the workpiece surface, applying an even, moderate
pressure until you reach the desired surface finish
WARNING: Excessive pressure does not lead to a faster removal of material; it will, however,
lead to premature wear of the sanding disc, and may cause damage to the machine.
If there are still scratches on your workpiece after sanding, refer to 'Selecting the right grade
of sanding disc'
Accessories
A range of accessories and consumables, including Hook & Loop Discs 60 – 240 Grit, is
available from your Silverline stockist. Spare parts can be obtained from toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
General inspection
Regularly check that all the fixing screws are tight
Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs should be
carried out by an authorised SILVERLINE service centre. This advice also applies to extension
cords used with this tool
Emptying the dust extraction bag
WARNING: Always switch off and disconnect from the power supply before detaching the dust
extraction system.
WARNING: Always wear respiratory protection, eye protection and gloves when emptying the
Dust Bag (5).
Note: For optimum dust removal, empty the Dust Bag when it is no more than half full.
1. Detach the Dust Bag from the Dust Extraction Port of the sander by pulling and twisting the
bayonet fitting on the Dust Bag Collar (6)
2. Dispose of the waste
3. Attach the Dust Bag to the Dust Extraction Port of the sander by pushing and twisting the
bayonet fitting on the Dust Bag Collar
Note: If the sanding dust contains harmful substances, such as particles from old paint, varnish,
surface coatings etc., always dispose of according to relevant laws and regulations.
Note: Always clean the tool THOROUGHLY when switching from sanding wood to sanding metal
and vice versa.
240W Random Orbit Sander
Cleaning
WARNING: ALWAYS wear protective equipment including eye protection and gloves when
cleaning this tool.
Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and
shorten the device's service life
Clean the body of your machine with a soft brush, or dry cloth
Never use caustic agents to clean plastic parts. If dry cleaning is not sufficient, a mild detergent
on a damp cloth is recommended
Water must never come into contact with the tool
Ensure the tool is thoroughly dry before using it
If available, use clean, dry, compressed air to blow through the ventilation holes (where
applicable)
Lubrication
Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
Over time the carbon brushes inside the motor may become worn
Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
If you suspect that the brushes may be worn, have them replaced at an authorised SILVERLINE
service centre
Storage
Store this tool carefully in a secure, dry place out of the reach of children
Contact
For technical or repair service advice, please contact the helpline on (+44) 1935 382 222
Web: www.silverlinetools.com
UK Address:
Toolstream Ltd.
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
EU Address:
Toolstream B.V.
Holtum-Noordweg 11
Unit 4
6121 RE Born
The Netherlands
Disposal
Always adhere to national regulations when disposing of power tools that are no longer functional
and are not viable for repair.
Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with
household waste
Contact your local waste disposal authority for information on the correct way to dispose of
power tools
silverlinetools.com
7

Publicidad

loading