Publicidad
Idiomas disponibles
Idiomas disponibles
• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing
maintenance.
• Avoid direct eye exposure to the light source while it is on.
•
WARNING RISK OF BURN
• Allow lamp/fixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer's warnings, recommendations, and restrictions for: driver type, burning position, mounting
locations/methods, replacement and recycling.
•
CAUTION RISK OF FIRE
• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances affected by heat or drying.
CAUTION RISK OF PRODUCT DAMAGE
•
• Never connect components under load.
• Do not mount or support these fixtures in a manner
that can cut the outer jacket or damage wire
insulation.
• Never connect an LED product to an unapproved
dimmer pack. Contact ABL directly for any dimmers
not specifically recommended for the product.
• Unless individual product specifications deem
otherwise: Allow for some volume of airspace around
fixture. Avoid covering LED fixtures with insulation,
foam, or other material that will prevent convection or
conduction cooling.
• Unless individual product specifications deem
otherwise: Maximum ambient temperature is 90°C.
Do not operate fixture at temperatures higher than
this.
• Unless individual product specifications deem
otherwise: Never mount in places where fixture will
•
CAUTION RISK OF WIRING PRODUCT DAMAGE
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply
with one of the following Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation.
One Lithonia Way · Conyers, GA 30012 · Phone 1-(800)705-7378
Visit us at
© 2024 Acuity Brands Lighting, Inc
INSTALLATION INSTRUCTIONS
www.acuitybrands.com/juno-recessed
.
Juno Wafer 2" LED Downlight-WF2 Series
be exposed to rain, high humidity, extreme
temperature changes or restricted ventilation.
• LED products are Polarity Sensitive. Ensure proper
Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage
LED fixtures. Personal grounding equipment must be
worn during all installation or servicing of the unit.
• Do not touch individual electrical components as this
can cause ESD, shorten lamp life, or alter
performance.
• There are no user serviceable parts inside the unit.
Do not rewire, reconfigure, or modify the unit or
attempt any repairs yourself. Additionally, field
replacement of the LED assembly or lamps is not
allowed by UL standards at this time. In the unlikely
event your unit may require service, stop using the
unit immediately and contact an ABL representative.
912-00497-001 REV A
DATE 01/2024
3
PAGE |
Publicidad
