KBS BAIN-MARIE ARMONIA Instalación Y Uso página 8

Operator's guide:
1)Unpacking instructions
2)Glass assembly
3)Opening the protective cover
4)Cleaning the internal basin
5)Cleaning the cover and external parts
6)Holders for containers
7)Connection to the mains
8)Operations and adjustment
9)Cleaning of the bain-marie basin
10)Filter cleaning
WARNINGS
!
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
1
. Adults should operate this appliance only. Do not allow children to use the controls or play with it. . It
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
4. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
5
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
6
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs.
7. The manufacturers of this appliance accept no responsibility for the consequences of misuse in
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice.
UNPACKING INSTRUCTIONS
1.
1a. Cut surrounding tape . Remove the cardboard package by sliding it upwards, remove the nails from
the wooden crate with care. . Lift the appliance, without putting pressure on the handgrip.
pallet or crate, thus disengaging the wheels of the appliance. . Make sure there is nothing left in the
package before disposing of it. . Sort out the packaging materials in order to facilitate disposal
(see picture 1)
GLASS ASSEMBLY
2.
1
. Unpack the glass panels. . Insert the glass side panels in the special U-brackets you will find in the
upper section of the cabinet (see figure 4). . Tighten the brackets' screws.
glass panels, insert the steel ceiling lamp assembly. . Fix the lamp assembly with the screws supplied.
6.
Protect the lamp cables with the profiles provided. . Assemble the front panel, inserting it into its seat
(see figure 5).
3. OPENING THE PROTECTIVE COVER
1
. Plug the machine into the power supply socket.
position II until the cover is fully open.
! N.B.: turn the heated shelves and heating lamps off ten minutes before lowering the cover
CLEANING THE INTERNAL BASIN
4.
1.
Remove the protection film from the stainless steel parts.
3
neutral detergents. . Remove obstructions in front of the float hole (A) and the drainage hole (B).
4. Open the tap located on the rear side of the machine to drain any residual water (see fig. 3).
5. CLEANING THE COVER AND EXTERNAL PARTS
1. Never use detergents containing alcohol or derivatives, or abrasive sponges and products, which
would irreparably damage the cover. . Use the same products as used for internal cleaning. . Use only
4
a soft wet sponge. . Dry with a soft clean cloth.
6. HOLDERS FOR CONTAINERS
1.
Remove the protection film from the holders.
3. Place the shorter holders on the special slots on the longer holders. Different arrangements are
available for different container sizes and positions. . Position the containers in accordance to your
requirements (see fig. 3).
7.
CONNECTION TO THE MAINS
1. Ensure that mains voltage and frequency are the same as those stated on the rating plate (A) attached
to the appliance (see picture 3). . Ensure that the supply socket:
requirements of the rated current as set out on the rating plate;
- thermal-magnetic switch with In = rated value as stated on the rating plate; - differential with Id
sensitivity = 30 mA.
Operator's guide
2
5
2
3
5
7
2.
Turn the switch of the electric lifting system (A) to
2
2.
Place the longer holders on the long sides of the basin.
4
2
7
Maintenance manual (Page 47):
1)Replacement of the lamps
2)Replacement of cover's lifting motor
3)Wiring diagram diagram of refrigeration unit
4
4.
Having assembled both
2.
Clean the basin with a soft sponge and
a) is properly earthed;
complies with the IEC regulations:
c)
UK
D
E
F
NL
P
2
3
S
DK
FIN
B
GR
CZ
3.
Remove the
EE
LV
LT
H
M
PL
SK
SLO
3
b) fulfils the
I