Publicidad
Idiomas disponibles
Idiomas disponibles
WELDING THROUGHT BAR CODE READING
Connect the BARCODE reader
and select the "READ BARCODE"
1.
Read the Welding barcode
Keep the trigger pressed and make
sure the LASER beam points out the
welding bar code.
Displayed parameters:
Junction type
e.g. I CPL PI
Voltage & Time
e.g. 39.5V 100s
Diameter
e.g. 32 mm
Note: In case of barcode scanner
failure you can still set the welding
parameters manually (below).
Press OK ► to proceed.
2.
Read the Traceability barcode
If Traceability option is enabled,
the Elektra will prompt to read the
traceability barcode.
In order to skip a traceability
barcode, press the OK ► button.
Keep the trigger pressed and make
sure the LASER beam points out the
traceability bar code.
The
bar
code
data
will
presented as in the example on the
right side, as scrolling text.
Press OK ► to proceed.
3.
Add a Note
If Note option is enabled, the
Elektra will prompt to type in some
note text.
Use ▲ and ▼ buttons to change
the digit value and OK ►button to
move to the next digit.
Hold OK ►button to store or move
to the last digit and press OK ►
4.
Scraping and Aligning
The machine asks you to confirm if
the scraping has taken place (on
page 13).
poor scraping and
alignment may compromise the
quality of the welded joint even
though the welding process was
carried out correctly.
Press OK ► to start the welding.
5.
Welding
The heating phase starts.
The
display
will
show
countdown till the welding process
is accomplished.
I CPL PI
39.5V 100s
32mm
OK?
Socket PE Virgin
32 mm SDR: 11
32mm
PE100 MFR not spec.
be
OK?
Note
TEXT TO
STORE
_ _ _ _ _ _ _ _ _ _
_ _ _ _ _ _ _ _ _ _
39.5V 100s Ok J
01:01
the
39%
6.
Cooling
After completion of the heating
phase, the display shows the
cooling status.
When the cooling countdown is
over, the Elektra beeps.
The leads can be disconnected
and the Elektra switched off.
don't
move
strain the joint during the cooling
phase. Wait till the cooling time
has elapsed.
the
Elektra
not perform a leak test on the
welded joint. The Elektra only
shows that all the welding phases
have
been
correctly
accomplished.
Ritmo
disclaims all liability for defective
welded
joints
made
without
regard to proper preparation of
the pipes end to be welded.
WELDING THROUGHT MANUAL INPUT OF BAR CODE
Select the "BARCODE MANUAL"
mode and
press OK ►.
1.
Type the welding barcode
digits
Use ▲ and ▼ buttons to change
the digit value and OK ►button to
move to the next digit.
2.
Follow the steps of
WELDING THROUGHT BAR CODE
READING on page 14.
WELDING THROUGHT MANUAL INPUT OF WELDING VOLTAGE AND
TIME
Select the "VOLTAGE-TIME" mode
and
press OK ►.
This mode requires the knowledge
of the welding voltage / time
parameters.
These parameters are generally
written/stamped on the coupler.
Contact the coupler manufacturer
if welding voltage and time are
unknown.
1.
Enter the voltage and time
values
Use ▲ and ▼ buttons to change
the digit value and OK ►button to
move to the next digit.
09:23
or
does
CT 11:32
# 482
S.p.A
9
7
0
9
1
4
4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
20.0 0120
EN
0
0
0
15
Publicidad
