Publicidad
Idiomas disponibles
Idiomas disponibles
STEP 4 -
Wiring the DCM (Single Door Install Shown with OHD Opener)
Before you begin, make sure the garage door opener is unplugged so the door does not move
unexpectedly.
1. Leaving the wire spool intact, split one end of the dual strand wire
approximately 2 in. then strip 1/2 in. of insulation (FIG. A)
2. On the terminal strip (back of the DCM), press down on the orange tabs and
insert 1 wire each into each of the two terminals for DOOR 1. Each DOOR number on
the terminal strip corresponds to a button on the front of the panel (FIG. B & C).
FIG.A
2"
1/2"
Split 2" & Strip 1/2"
Press tab down
Press tab down
Button & Connection Detail
to install wire.
to install wire.
FIG.C
Door
Door
Door
NOTE: This Wi-Fi retrofit kit can control
1
2
3
up to 3 garage door openers.
STEP 6
Mount and Power OHD Anywhere®:
1.
Using the DCM mounting bracket as a template at the optimal
Wi-Fi location. Mark and drill 2-3/32" pilot holes and mount
bracket to wall using supplied screws. If mounting to drywall,
use anchors provided in kit or if mounting to perforated angle
at opener location, use nuts, washers and screws provided.
2.
Plug Power Pack into wall outlet. An extended screw is provided
to secure Power Pack to outlet if needed.
3.
Plug Power Pack into back of DCM as shown in
STEP
NOTE: LEDs on DCM will flash momentarily as it reacquires signals.
4.
Snap DCM onto mounting bracket.
5.
Route wires and secure with supplied staples.
6.
Affix the warning placard next to wall control or DCM in plain
sight to signify that the door will operate remotely.
7.
Tacks or staples should be used if the placard does not adhere
to the mounting surface.
Wall Mount
Perforated Angle
1
Anchors (as needed)
2-4
6
WARNING
AVERTISSEMENT
MOVING DOOR can cause serious
injury or death.
STAND CLEAR!
Door could close automatically.
Do Not stop or stand in doorway
MOUVEMENT PORTE peut causer des
blessures graves ou la mort.
SE TENIR À L'ÉCART DE LA PORTE!
La porte pourrait se refermer automatiquement.
Ne pas arrêter ou debout dans la porte.
STEP 5a -
There are two ways to wire the DCM for power. Please review Options 1 and 2 for
Wiring steps.
1. Remove the wall control push button and locate screw terminals on the
2. Cut the dual wire strand and split the end ~2 in. and then l strip 1/2 in. of
3. Add the black/white wire from the DCM to the screw with the black/white
4. Add the white/white wire from the DCM to the other screw on the wall control.
FIG. B
STEP 7
Mount DPS Module to Garage Door:
TAB" from DPS until
DO NOT remove the battery
"PULL
directed by the app.
The DPS should be mounted on the TOP door panel only.
Mount to steel reinforced end stile on the far left or right
under the top hinge. DO NOT mount to unreinforced door
panel.
1.
Clean door where DPS will mount.
2.
Install double sided tape to back of mounting bracket and affix to
1.
door.
NOTE: Double sided tape is designed to hold bracket in place temporarily
only. Not to be used for permanent mounting.
3.
Pre-drill 2 - 3/32 holes. DO NOT drill all the way through door.
4.
Use included self tapping screws to mount DPS bracket to top door
panel end stile.
5.
Slide DPS down onto mounting bracket. DPS should snap onto
bracket.
NOTE: The DPS included with this kit is already programmed to the DCM. See
Mount
the NOTE under
STEP 8
regarding additional sensors (DPS).
STEP 8
Complete the Programming:
1.
Restore power to the garage door opener.
2.
Operate the door with the wall control. Open the OHD Anywhere app and verify that the door position in the app is accurate.
NOTE: This kit includes one DPS for use with one door only. The DPS included is already programmed to the DCM . Additional sensors can be purchased separately
from your local Overhead Door retailer. To program additional sensors, first complete STEP 8 initial setups and programming, then go to "Add a Door Sensor" under
the "Doors" tab inside the app or view the installation video at www.OverheadDoor.com/OHDAnywhere/InstallationVideo.
NOTE: A white light will flash and an audible beep will sound as an indication that the door is about to move when commanded by OHD AnyWhere® or other
compatible app(s).
Use of this product, the software embedded within this product and the related application software is subject to the Terms and Conditions available at: www.OverheadDoor.com/OHDAnywhere
112612.0001
Option 1 - Wiring to Wired Wall Control
back.
insulation (FIG. A)
wire on the wall control.
FIG. D
OR
NOTE: Wires are polarity sensitive at the wall console terminals.
Check your opener manual to review proper terminal wiring as needed.
STEP 5b -
Option 2 - Wiring to Garage Door Opener
1. Find the terminals for the push button wired wall console
a. If your garage door opener has screw terminals, connect one wire to the
push button terminal and the other to the common (comm) terminal.
b. If your garage door opener has colored terminals, wire to the red and
white terminals (or R and W).
to opener
NOTE: Garage door openers have terminal strips or screw terminals to connect to
to DCM.
safety beams (STB or Beam) AND to the wall control push button (PB or also called
a basic wall control - BWC). The wiring from the door control module connects with
existing wires going to the wall control push button terminals. You can review the
garage door opener manual to see which terminals are for the push button or just
trace the wire from the push button to the opener.
Mounting DPS
END STILE
Garage Door
Garage Door
P.B. COM. BEAM
Need help? Call us at 1-888-901-2750 or
scan the QR codes for additional support.
Scan for the
OHD Anywhere®
installation video
Scan here for additional
OHD Anywhere®
information
©2023 Overhead Door Corporation, One
Door Drive, Mt. Hope, OH 44660, USA
1-year warranty, visit www.
overheaddoor.com for details.
Pat. www.overheaddoor.com/
Documents/Patents-Overhead-Door.pdf
Publicidad
