Publicidad
Idiomas disponibles
Idiomas disponibles
EnGLIsh
down if necessary. The red LED indicator
the ANTI‑ROTATION System is engaged.
InDICaTOR DIaGnOsIs
OFF
Tool is functioning
normally
SOLID RED
ANTI‑ROTATION
System has
been activated
(ENGAGED)
Side Handle (Fig. D1–D4)
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed.
Failure to do so may result in the side handle slipping
during tool operation and subsequent loss of control. Hold
tool with both hands to maximize control.
The side handle
clamps to the front of the gear case and
14
may be installed in multiple positions to permit right‑ or
left‑hand use. After the side handle is rotated into position, it
should be pushed rearward until the slots
side handle are aligned and fully engaged with the projecting
tabs
on the top and bottom of the gear case. The side
17
handle is then securely clamped by turning the handle grip
clockwise until tight. Be sure to grip the side handle at the far
end on the handle grip to control the tool during a stall.
IMPORTanT: Figures D3 and D4 illustrate correct and incorrect
installation of the side handle.
Installing a Bit or Accessory into a Keyless
Chuck (Fig. C)
WARNING: Do not attempt to tighten drill bits (or
any other accessory) by gripping the front part of the
chuck and turning the tool on. Damage to the chuck
and personal injury may result. Always lock off trigger
switch and disconnect tool from power source when
changing acces sories.
WARNING: Always ensure the bit is secure before starting
the tool. A loose bit may eject from tool causing possible
personal injury.
WARNING: The keyless chuck is unlocked after the first
click in the counterclockwise direction with the chuck
sleeve. Operation in the unlocked condition may cause
unintentional opening of the keyless chuck.
To insert a drill bit or other accessory, follow these steps.
1. Turn tool off and remove battery pack.
2. Grasp the black sleeve of the chuck with one hand
and use the other hand to secure the tool. Rotate the
sleeve counterclockwise far enough to accept the
desired accessory.
3. Insert the accessory about 3/4" (19 mm) into the chuck
and tighten securely by grasping and rotating the chuck
sleeve
7
clockwise with one hand while holding the tool
with the other. When the chuck is nearly tightened you will
38
38
22
illuminates when
sOLUTIOn
Follow all warnings and instructions
when operating the tool.
With the tool properly supported,
release trigger. The tool will function
normally when the trigger is
depressed again and the indicator
light will go out.
16
on the lip of the
hear a clicking sound. Continue tightening as far as you
can. Your tool is equipped with an automatic spindle lock
mechanism. This allows you to open and close the chuck
with one hand.
4. Be sure to tighten the chuck with one hand on the
chuck sleeve and one hand holding the tool for
maximum tightness. When tightening, do not turn in the
counterclockwise direction.
5. To release the accessory, repeat steps 1 and 2 above.
Mode Selection (Fig. A)
The mode selection collar
operating mode depending upon the planned application.
To select, rotate the collar until the desired symbol aligns with
the arrow.
WARNING: When the mode selection collar is in the drill,
the drill will not clutch. The drill may stall if overloaded,
causing a sudden twist.
Speed Selection (Fig. A)
The tool features three speed settings for greater versatility.
nOTE: Do not change speeds when the tool is running.
Always allow the tool to come to a complete stop before
changing speed.
18
•
To select speed 1 (highest torque setting), turn the tool
off and permit it to stop. Slide the speed selector
way forward.
•
Speed 2 (middle torque and speed setting) is in the
middle position.
•
Speed 3 (highest speed setting) is to the rear.
If the tool does not change speeds, confirm that the speed
selector is completely engaged in the forward or back position.
If trouble shifting gears persists, depress and release the trigger
switch and try again.
OPERATION
Instructions for Use
WARNING: Always observe the safety instructions and
applicable regulations.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. H)
WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.
WARNING: To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Proper hand position requires one hand on the main
6
handle
, with the other hand on the side handle
15
control the twisting action of the drill.
can be used to select the correct
5
14
8
all the
to
Publicidad
